Basic Playback; Playing A Source; Selecting The Audio Input Signal - Pioneer HTP-072 Operating Instructions Manual

03

Basic playback

03
Chapter 3:
Basic playback

Playing a source

Here are the basic instructions for playing a source (such as
a DVD disc) with your home theater system.
TV
RECEIVER
SLEEP SOURCE CONTROL
PARAMETER
RECEIVER INPUT SELECT
TOP
INPUT
MENU
BD DVD CD
CH
TUNER iPod/USB SAT/CBL
HOME
MENU
PTY
GAME TV SIGNAL SEL
1 Switch on your system components and receiver.
Start by switching on the playback component (for example a
DVD player), your TV and subwoofer (if you have one), then
the receiver (press  RECEIVER).
• Make sure the setup microphone is disconnected.
2 Switch the TV input to the input that connects this
receiver.
For example, if you connected this receiver to the VIDEO
jacks on your TV, make sure that the VIDEO input is now
selected.
3 Press input function buttons to select the input function
you want to play.
• The input of the receiver will switch over, and you will be
able to operate other components using the remote
control. To operate the receiver, first press
the remote control, then press the appropriate button to
operate.
• The input source can also be selected by using INPUT
buttons on the remote control, or by
SELECT
using the front panel INPUT SELECTOR dial. In this case,
the remote control won't switch operational modes.
18
En
If you selected the proper input source and there is still no
sound, select the audio input signal for playback (see
Selecting the audio input signal below).
4 Press AUTO/DIRECT to select 'AUTO SURROUND' and
start playback of the source.
If you're playing a Dolby Digital or DTS surround sound DVD
disc, with a digital audio connection, you should hear
surround sound. If you're playing a stereo source or if the
connection is an analog audio connection, you will only hear
sound from the front left/right speakers in the default
AUTO/ ALC/
DIRECT STEREO STANDARD ADV SURR
listening mode.
ECO
It is possible to check on the front panel display whether or
AUDIO TOOLS
MENU VOLUME
not surround sound playback is being performed properly.
If the display does not correspond to the input signal and
listening mode, check the connections and settings.
ENTER
Note
• You may need to check the digital audio output settings
BAND
iPod CTRL RETURN on your DVD player or digital satellite receiver. It should
MUTE
be set to output Dolby Digital, DTS and 88.2 kHz/96 kHz
PCM (2 channel) audio, and if there is an MPEG audio
option, set this to convert the MPEG audio to PCM.
• Depending on your DVD player or source discs, you may
only get digital 2 channel stereo and analog sound. In this
case, the receiver must be set to a multichannel listening
mode if you want multichannel surround sound.
5 Use VOLUME +/– to adjust the volume level.
Turn down the volume of your TV so that all sound is coming
from the speakers connected to this receiver.

Selecting the audio input signal

The audio input signal can be selected for each input source.
Once it is set, the audio input that was selected will be
applied whenever you select the input source using the input
function buttons.
on
RECEIVER
CH
TUNER iPod/USB SAT/CBL
GAME TV SIGNAL SEL
VOL
Acous.EQ S.RETRIEVER PHASE
1 Press SIGNAL SEL to select the audio input signal
corresponding to the source component.
Each press cycles through the following:
• H – Selects an HDMI signal. H can be selected for BD,
DVD, SAT/CBL and GAME input. For other inputs, H
cannot be selected.
When the HDMI option in Setting the Audio options on
-
page 25 is set to THRU, the sound will be heard through
your TV, not from this receiver.
• A – Selects the analog inputs.
• C1/O1 – Selects the digital input. The coaxial 1 input is
selected for C1, and the optical 1 audio input is selected
for O1.
When H (HDMI) or C1/O1 (digital) is selected and the
selected audio input is not provided, A (analog) is
automatically selected.
Except BD, DVR/BDR input.
Note
• BD and GAME inputs are fixed to H (HDMI). It cannot
be changed.
For the TV input, only A (analog) or
•
be selected. However, if the ARC at
to ON, the input is fixed to H (HDMI) and cannot be
changed.
• When set to H (HDMI) or C1/O1 (digital), 2 lights when
a Dolby Digital signal is input, and DTS lights when a DTS
signal is input.
• When the H (HDMI) is selected, the A and DIGITAL
indicators are off (see page 7).
(digital) can
C1/O1
is set
HDMI Setup