Table of Contents
Advertisement
Troubleshooting
Troubleshooting
Possible causes
i There is no battery in the camera.
The self-timer lamp
i The battery is loaded backward.
does not light when
i The camera and AC power adapter are
charging the battery.
not connected correctly.
i The battery terminals are dirty.
The self-timer lamp
blinks during charging
and the battery won't
charge.
i The battery can no longer be recharged.
i The battery has run out.
No power.
i The AC power adapter plug has come
out of the power outlet.
i The battery is loaded backward.
i The battery cover is not closed correctly.
i The camera has been left for a long
period with battery and AC power
adapter removed.
The battery has run out.
Power cuts out during
operation.
i Camera is used in extremely cold
Battery
runs
out
conditions.
quickly.
i The terminals are soiled.
i The battery can no longer be recharged.
i No xD-Picture Card is inserted.
No photograph is taken
i The xD-Picture Card is full.
when pressing the
shutter button.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has turned
the camera off.
i The battery has run out.
i The shutter button was pressed while
Cannot use the flash.
the flash was charging.
i Photography mode is set to "
i Continuous shooting is selected.
The Photography mode is set to "
The flash settings are
À
,
.
"
", "
", "
", "
restricted and cannot
be selected.
i The subject is too far away.
The playback image is
dark even though the
i Your finger was covering the flash.
flash was used.
i The lens is dirty.
The image is blurred.
i You photographed scenery with Macro
mode selected.
i You took a close-up shot without
selecting Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
The picture was taken with a slow shutter
There is speckling on
speed (long exposure) in a high-
the image.
temperature environment.
118
eIf you think the camera is faulty, check the following once more.
Solutions
i Load the battery.
i Load the battery in the correct direction.
i Connect the camera and AC power
adapter correctly.
i Take the battery out briefly and then
reload it.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new battery. If the battery still
fails to charge, contact your FUJIFILM
dealer.
i Load a fully charged battery.
i Plug the adapter back in.
i Load the battery in the correct direction.
i Close the battery cover correctly.
i Load the battery or connect the AC
power adapter, and wait a short time
before turning the camera on.
Load a fully charged battery.
i Put the battery in your pocket or another
warm place to heat it and then load it
into the camera just before you take a
picture.
i Wipe the battery terminals with a clean,
dry cloth.
i Load a new battery.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or erase
some unnecessary frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact area
with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load a fully charged battery.
i Wait until the charging is completed
before pressing the shutter button.
À
" or "
,
".
i Change the Photography mode.
i Set continuous shooting to "OFF".
B
",
The flash settings are restricted because
©
M
<
", "
" or "
".
the camera settings are tailored to the
scene
being
shot.
Photography mode for a wider range of
flash settings.
i Move to within the effective flash range
before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
This is a characteristic of CCDs and does
not indicate a camera fault.
Troubleshooting
The camera does not
emit any sound.
Frame erase does not
erase the frame.
The
ERASE
function does not erase
all the frames.
Screens
displayed in English.
There is no image or
sound on the TV.
The TV image is black
and white.
When connecting the
camera to a PC, the
photographed image or
playback
appears
camera's LCD monitor.
Nothing happens when
using the Mode switch.
The camera no longer
works correctly.
Change
the
Cannot
PictBridge.
The
camera
connected to a PC
when the USB mode
was set to "
Possible causes
i The camera volume is set too low.
i The microphone was blocked during
shooting/recording.
i There is something covering the speaker
during playback.
Some frames may be protected.
ALL
are
not
A language other than English is selected
in the "
ô
"
setting in the "
SET-UP menu (➡P.88).
i The included A/V cable was connected
during movie playback.
i The camera is not connected to the TV
correctly.
i "TV" is selected as the TV input.
i The "
õ
" video output setting is
incorrect.
i The TV volume is turned down.
õ
The "
" video output setting is incorrect.
i The USB cable (mini-B) is not correctly
connected to the PC or camera.
i The PC is not turned on.
image
on
the
i Camera malfunction.
i The battery has run out.
The camera has suffered an unforeseen
problem.
print
with
®
"
" PICTBRIDGE is not selected in "
˜
USB mode in the "
" SET-UP menu.
was
®
".
Solutions
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is
uncovered.
Unprotect frames using the camera on
which the protection was first applied.
1Press the "MENU/OK" button to display
˜
"
the menu.
2Press "
˜
a
" or "
b
" to select "
" SET-UP
and press "
c
".
3Press "
" or "
" to select "
ô
"
a
b
4Press "
".
c
5Press "
a
" or "
b
" to select "ENGLISH".
6Press the "MENU/OK" button.
i After the movie playback mode is stopped,
connect the camera and TV correctly.
i Connect the camera and TV correctly.
i Set the TV input to "VIDEO".
i Change the setting to "NTSC" or "PAL"
(➡P.88).
i Adjust the volume.
Change the setting to "NTSC" or "PAL"
(➡P.88).
i Set up the camera, and connect the USB
cable (mini-B) correctly.
i Turn the PC on.
i Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power
adapter and try again.
i Load a fully charged battery.
Briefly remove the battery or disconnect
the AC power adapter. Then reload the
battery or reconnect the AC power adapter
and try again. If you think the camera is
faulty, contact your FUJIFILM dealer.
ò
®
ò
"
Select "
" PICTBRIDGE in "
" USB
˜
mode in the "
" SET-UP menu.
Perform steps 1 to 3 to remove the
camera from the PC.
h Windows
1 The "New Hardware Found" wizard or
"Scanner and Camera" wizard appears.
If the wizard does not appear, proceed
to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the PC.
h Macintosh
1 The window for locating the driver
appears. If the window does not
appear, proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the
Macintosh.
119
Hide quick links:
Advertisement
Table of Contents
