1. Manuals
  2. Brands
  3. SMC Networks Manuals
  4. Network Router
  5. EZ Connect SMC7003ADSL
  6. User manual

SMC Networks SMC7003ADSL User Manual

Adsl bridge/router
Hide thumbs Also See for SMC7003ADSL:
Table of Contents

Advertisement

Quick Links

Download this manual
ADSL Bridge/Router
SMC7003ADSL
Read Me First
User's Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SMC7003ADSL and is the answer not in the manual?

Questions and answers

Related Manuals for SMC Networks SMC7003ADSL

Summary of Contents for SMC Networks SMC7003ADSL

  • Page 1 ADSL Bridge/Router SMC7003ADSL Read Me First User’s Manual...
  • Page 2 Information contained within this document is subject to change. Revision to this document, or new additions to it, may be issued to incorporate such changes. Revision Status: Model number Rev. Date Change SMC7003ADSL February 2001 Preliminary SMC7003ADSL (version 1.0)

  • Page 3: Packing List

    Introduction Introduction The SMC7003ADSL provides unrivaled asymmetric high-speed data transport over a single copper pair. Its very rich feature set includes an easy to use Setup Wizard, DHCP support, a firewall for network protection and VPN capabilities for reduced cost of remote access communications.

  • Page 4: Table Of Contents

    Default Settings Installation Chapter 2 Hardware Installation Procedures 2.1.1 Ethernet Connection 2.1.2 USB Connection Connecting the PC to the SMC7003ADSL 2.2.1 Ethernet Connection 2.2.2 USB Installation 2.2.2.1 How to install the USB Driver 2.2.2.2 Configuring the PC for the USB Configuration...

  • Page 5: Product Description

    For Ethernet connectivity to our system, you can use any Operating System with the TCP/IP protocol such as Linux, Mac, OS2 etc. 1.2 Physical Descriptions The SMC7003ADSL is a compact, light-weight communications device with the following dimensions: Height : 1.5"...

  • Page 6: Front Status Indicators

    Green (solid) illuminates indicate successful connection to the Network. ALARM Red (solid) It indicates the device encountering an error. Green (solid/blinking) ATM ACT The ATM Activity LED shows data traffic. During normal operation, it should be blinking. SMC7003ADSL (version 1.0)

  • Page 7: Rear Panel

    RESET SWITCH To return the device to factory settings. ETHERNET Allows the SMC7003ADSL to establish a connection either to a hub or directly to a PC and requires a RJ-45 cable (provided). It has 2 LEDs. The Link LED (green) remains solid when connected to an active Ethernet port.

  • Page 8: Parameters From Service Provider

    255 . 255 . 255 . 0 Gateway Address 10 . 10 . 12 . 1 DNS Server Address 202 . 23 . 3 . 75 Domain Address 10 . 10 . 12 . 40 vci value (default: vci=35) vpi value (default: vpi=0) SMC7003ADSL (version 1.0)
  • Page 9 If vci/vpi values are the same as the default, you do not need to make any changes in the Bridge Mode. a Extra copy of this page is provided on the last page of this manual. SMC7003ADSL (version 1.0)

  • Page 10: Default Settings

    : 10.0.0.1 subnet-mask : 255.255.255.0 user name : admin password : password (minimum 4 alphabetic characters) language : english ATM MODULE vc-no : 35 vc-type : ATM_PVC encap type : LLC_MUX encap protocol : RFC1483 (BRIDGED) SMC7003ADSL (version 1.0)

  • Page 11: Installation

    Chapter 2 - Installation Chapter 2 - Installation 2.1 Hardware Installation Procedures The following steps are recommended to complete the SMC7003ADSL installation and setup procedures. Cable connections to the Rear Panel of the SMC7003ADSL. SMC7003ADSL (version 1.0)

  • Page 12: Ethernet Connection

    (If the TCP/IP protocol is not installed, go to Appendix B for the installation procedures). Connect the Ethernet cable (yellow) from the SMC7003ADSL’s Ethernet port to the Ethernet port of the PC. Connect the DSL cable (green) in to the DSL wall jack and the other end in to receptacle marked “DSL RJ-11”...

  • Page 13: Usb Connection

    Plug the square side of the USB cable’s one end (grey cable) in to the SMC7003ADSL device’s USB port and the other flat long end to the USB port of the PC. (If the PC is running, it will automatically detect the USB port Driver).

  • Page 14: Connecting The Pc To The Smc7003Adsl

    1. Follow Steps 1 through 5 as shown on the next page and restart the PC. 2. In Step 5, the IP address needs to be of the same class as the SMC7003ADSL. For example: The IP address should be 10.0.0.2 if the default IP address of the unit is 10.0.0.1.
  • Page 15 Chapter 2 - Installation 1. Click Start on the Task Bar of the PC, select Settings and select Control Panel. 2. Double-click the Network icon. 3. In the Configuration window, select the TCP/IP Protocol associated with the installed Ethernet card. SMC7003ADSL (version 1.0)
  • Page 16 4. Click the Properties button and select IP Address tab. 5. Select Specify an IP Address and fill in the fields with the IP Address and Subnet Mask from the work sheet. 6. Continue the settings by clicking the Gateway tab. SMC7003ADSL (version 1.0)
  • Page 17 Chapter 2 - Installation 7. Enter the Gateway IP Address from the work sheet. 8. Click Add. 9. Click the DNS Configuration tab to continue with the settings. SMC7003ADSL (version 1.0)
  • Page 18 11. Enter Host name and Domain name from the work sheet. 12. Under the DNS Server Search Order, enter the DNS Server IP Address as entered in the work sheet. 13. Click Add. 14. Click OK and follow instructions to restart the PC. SMC7003ADSL (version 1.0)

  • Page 19: Usb Installation

    A window shows the USB driver loading. Click Finish and the Wizard window will show that it has detected another driver SMC7003ADSL vv PC-attached gateway. Click Next. Select the CD Drives and click Next. The PC will begin loading the second USB driver which is vvbeth.sys.

  • Page 20: Configuring The Pc For The Usb

    1. Click Start on the Task Bar of the PC, select Settings and Control Panel. 2. Double-click the Network icon. 3. From the Configuration window, select the TCP/IP protocol which shows TCP/IP SMC7003ADSL VVB PC-attached gateway. 4. Follow Step 4 through Step 14 from the Ethernet Connection to complete the setup.

  • Page 21: Configuration

    Chapter 3 - Configuration Chapter 3 - Configuration 3.1 GUI Installation The following procedures are recommended to configure the SMC7003ADSL through the GUI. Before you begin, you need to install the GUI software from the 3 1/2" Floppy Diskette provided in the package.

  • Page 22: Easy Setup Flow Chart

    EXIT CONFIGURE: Parameters for Ethernet and/ or USB ports Note : Ethernet-the unit can distribute IP address to more than 1 PC on the network ENTER: DSL Parameters Note : DSL Parameters provided by Service Provider EXIT SMC7003ADSL (version 1.0)

  • Page 23: Login Screen

    Chapter 3 - Configuration 3.3 Login Screen • The Device Type is Ethernet. • Choose admin under the User Name and enter the password as password. • Click Login. • The default choice is Easy Setup. • Click OK. SMC7003ADSL (version 1.0)

  • Page 24: Bridge Mode Configuration

    • Click Next to change current Bridge configuration. Enter the LAN IP address • (shown is the default LAN IP address of the SMC7003ADSL) • Enter the DSL Parameters in the WAN Parameters boxes entered from the work sheet. •...
  • Page 25 Chapter 3 - Configuration • The SMC7003ADSL Status Window will appear as shown above. Select DSL or IP to view the current statistics. • • Or select Advanced to make further changes in the configuration. • Select Save and Exit to exit the GUI.

  • Page 26: Router Mode Configuration

    Cancel. • If you want to make changes, in ‘Do you want to change to Routed Mode?’, choose Yes. • Click Next. • Choose the Device Type i.e: Ethernet or Ethernet and USB. Click Next. • SMC7003ADSL (version 1.0)
  • Page 27 Enter the WAN IP Address as entered in the work sheet. • Enter the Gateway Address. Enter The vpi/vci values. • (The default vpi/vci values are 0 and 35). • Enable or Disable NAT as required. Click Finish. • SMC7003ADSL (version 1.0)
  • Page 28 Chapter 3 - Configuration • The SMC7003ADSL Status Window will appear as shown above. • Select DSL or IP to view current statistics. • Or select Advanced to make further changes in the configuration. • Select Save and Exit to exit the GUI.

  • Page 29: Warranty And Shipping Information

    From Europe (8.00 AM - 5.30 PM UK Greenwich Mean Time) : 44 - 0 - 11 - 89 74 8740 : 44 - 0 - 11 - 89 74 8741 INTERNET E-Mail Addresses: techsupport@smc.com european.techsupport@smc-europe.com Driver Updates: http://www.smc.com/smc/pages_html/support.html World Wide Web: http://www.smc.com FTP Site: ftp://ftp.smc.com SMC7003ADSL (version 1.0)

  • Page 30: Smc's Limited Warranty

    4.2 SMC’s Limited Warranty Limited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, under normal use and service, for the applicable warranty term. All SMC products carry a standard 90-day limited warranty from the date of purchase from SMC or its Authorized Reseller.
  • Page 31 IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. SMC7003ADSL (version 1.0)
  • Page 32 * SMC will provide warranty service for one year following discontinuance from the active SMC price list. Under the limited lifetime warranty, internal and external power supplies, fans, and cables are covered by a standard one-year warranty from date of purchase. SMC7003ADSL (version 1.0)

  • Page 33: Appendix Afcc Notice

    Appendix A - Fcc Notice According to Federal Communications Commission (FCC) Rules regarding radio frequency emissions, the SMC7003ADSL complies with FCC Part 15 for Class B computing devices. The following paragraph is required by the FCC. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with this document, may cause interference to radio communications.
  • Page 34 This product conforms with Canadian Class B Emissions Regulations. Meets Approvals Safety : FCC Part 68, EN60950, UL 1950, C/UL to CSA 22.2 No.950, TUV, IC CS03 Emissions : FCC Part 15 Class B, EN55022 / CISPR2 Class B Immunity : EN55024 SMC7003ADSL (version 1.0)

  • Page 35: Appendix B Installation Of Tcp/Ip Protocol

    Windows NT and Windows 2000, please refer to the Windows manual. Click Start on the Task Bar of the PC and select Settings and Control Panel. Double-click the Network icon. Select the Configuration tab. Click on Add. Select Network Component Type i.e: Protocol and Click Add. SMC7003ADSL (version 1.0)
  • Page 36 The PC will return to the main Network window. Check if the TCP/IP Protocol appears in the list. Click OK. Windows may ask for the Windows95/98 CD or the original installation files (i.e.: D:/win95, D:/win98 or c:\windows\options\cabs). Click OK and follow instructions to restart the PC. SMC7003ADSL (version 1.0)

  • Page 37: Appendix C Interface Pin Assignments

    Appendix C - Interface Pin Assignments Appendix C - Interface Pin Assignments Digital Subscriber Line (RJ-11) Signal Name Ring Ethernet (RJ-45) Signal Name RD + RD - TD + TD - SMC7003ADSL (version 1.0)
  • Page 38 ___ . ___ . ___ . ___ vci value (default: vci=35) vpi value (default: vpi=0) NOTE: aIf vci/vpi values are the same as the default, you do not need to make any changes in the Bridge Mode. SMC7003ADSL (version 1.0)

Table of Contents