Related Manuals for AMX PLB-AMP8
Summary of Contents for AMX PLB-AMP8
- Page 1 PLB-AMP8 8-Channel Audio Power Amplifier L a n d m a r k P r o d u c t s...
- Page 2 This warranty extends only to products purchased directly from AMX Corporation or an Authorized AMX Dealer. AMX Corporation is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages. AMX Corporation is not liable for any claim made by a third party or by an AMX Dealer for a third party.
-
Page 3: Safety Instructions
10. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect if from overheating. These openings must not PLB-AMP8 8-Channel Audio Power Amplifier... - Page 4 18. Overloading - Do not overload wall outlets, extension cords, or integral convenience receptacles, as this can result in a risk of fire or electrical shock. PLB-AMP8 8-Channel Audio Power Amplifier...
- Page 5 24. Wall or Ceiling Mounting - The product should be mounted to a wall or ceiling only as recommended by the manufacturer. PLB-AMP8 8-Channel Audio Power Amplifier...
-
Page 6: Fcc Notice
Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Consult the dealer or an experienced radio/TV technician for help. PLB-AMP8 8-Channel Audio Power Amplifier... -
Page 7: Table Of Contents
Setting Channel Volume Levels Manually................. 2 Procedure for Setting Channel Volume Levels: ..............3 PHASTLink Ports ......................4 Line-Level Inputs ....................... 4 Speaker-Level Outputs...................... 4 Fuses..........................4 PHASTLink Cable Information ................5 Building a Double 120-ohm Terminator................6 PhastLink Connections...................... 7 PLB-AMP8 8-Channel Audio Power Amplifier... - Page 8 Table of Contents PLB-AMP8 8-Channel Audio Power Amplifier...
-
Page 9: Product Information
Product Information Product Information The PLB-AMP8 (FIG. 1) provides eight channels of amplification. The gain for each channel can be controlled from a variety of points, including PHASTLink devices, push-button controls at the back of the amplifier, and via a PC, using the amplifier's properties page in the Landmark software. -
Page 10: Connection And Power-Up Procedure
The individual LEDs above each channel (FIG. 3) indicate the selected channels. The right-arrow button (FIG. 2) at the upper left corner of the rear panel is used to cycle through the different channel selection choices and then enter Save mode or Idle mode, as follows: PLB-AMP8 8-Channel Audio Power Amplifier... -
Page 11: Procedure For Setting Channel Volume Levels
7. Press the down-arrow button (No) to cancel the save. If you wait too long while SA is displayed, the changes will not be saved. When power is cycled, the amplifier will return to the last level you saved. PLB-AMP8 8-Channel Audio Power Amplifier... -
Page 12: Phastlink Ports
Do not use excessive force. There should be no more than two units connect to a single 20 A breaker. PLB-AMP8 8-Channel Audio Power Amplifier... -
Page 13: Phastlink Cable Information
PHASTLink Cable Information PHASTLink Cable Information This section contains information that you will need to make PHASTLink cables, plus general information on connecting PHASTLink devices. PHASTLink cables are used to connect all PHASTLink-compatible devices, including keypads, dimmers, J-box IR devices, amplifiers, audio switches, etc. PHASTLink uses a standard 10BaseT connection (i.e. -
Page 14: Building A Double 120-Ohm Terminator
PHASTLink Cable Information To other PHASTLink devices (up to 500 mA total, or 10 devices - whichever comes first) Up to 15 PHASTLink connections to a PLB-CF10 Cardframe - up to 500 mA per port (add PHAST hubs for more connections). PLB-CF10 Cardframe FIG. -
Page 15: Phastlink Connections
PHASTLink Cable Information PhastLink Connections FIG. 3 shows how PHASTLink and HubLink ports are connected in a Landmark system. PLB-CF10 CardFrame HubLink PLH-RPT Hub HubLink PHASTLink Device PHASTLink Device Terminate the unused port PLH-MIC Hub HubLink PHASTLink PHASTLink Terminate the unused port FIG. - Page 16 DALLAS, TEXAS • LOS ANGELES, CALIFORNIA • MEXICO CITY, MEXICO • ONTARIO, CANADA • PHILADELPHIA, PENNSYLVANIA • SHANGHAI, CHINA • SINGAPORE • TAMPA, FLORIDA • WESTERLO, BELGIUM • YORK, ENGLAND 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com...