AMX DAS-TAMP4-SIG Operation/Reference Manual
  1. Manuals
  2. Brands
  3. AMX Manuals
  4. Amplifier
  5. DAS-TAMP4-SIG
  6. Operation/reference manual

AMX DAS-TAMP4-SIG Operation/Reference Manual

Tango amplifiers
Hide thumbs Also See for DAS-TAMP4-SIG:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Installation Manual
Operation/Reference Guide

Tango Amplifiers

DAS-TAMP4-SIG
DAS-TAMP8-SIG
T a n g o D i s t r i b u t e d A u d i o
I n i t i a l R e l e a s e : 3 / 2 8 / 2 0 0 8

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DAS-TAMP4-SIG and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for AMX DAS-TAMP4-SIG

Summary of Contents for AMX DAS-TAMP4-SIG

  • Page 1: Tango Amplifiers

    Operation/Reference Guide Tango Amplifiers DAS-TAMP4-SIG DAS-TAMP8-SIG T a n g o D i s t r i b u t e d A u d i o I n i t i a l R e l e a s e : 3 / 2 8 / 2 0 0 8...
  • Page 2 AMX is not responsible for products returned without a valid RMA number. AMX is not liable for any damages caused by its products or for the failure of its products to perform. This includes any lost profits, lost savings, incidental damages, or consequential damages.

  • Page 3: Important Safety Instructions

    IMPORTANT SAFETY INSTRUCTIONS Read instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
  • Page 4 IMPORTANT SAFETY INSTRUCTIONS Tango Amplifiers...

  • Page 5: Table Of Contents

    Table of Contents IMPORTANT SAFETY INSTRUCTIONS ... a Tango Amplifiers ...1 Overview ... 1 Product Specifications ... 1 Rack Mounting ...3 Overview ... 3 Ventilation ... 3 Wiring and Connections ...5 Overview - Speaker Wire Technology (SWT)... 5 Front and Rear Panel Components ... 5 Cabling Instructions ...
  • Page 6 Table of Contents Tango Amplifiers...

  • Page 7: Tango Amplifiers

    Integrates with Tango Series, Delta Series and Mi Series controllers, as well as the W, C, C-DT and EL Series speakers. The DAS-TAMP4-SIG Tango 4-Channel Amplifier (FG1103-21) is a 4-channel amp that supports an additional 2 speaker pairs per unit.
  • Page 8 Tango Amplifiers Tango Amplifiers - Product Specifications (Cont.) Front Panel Components: Light Bar Status LED Rear Panel Components: Power Switch & Receptacle The master power switch will remain in the ON position normally. Output 1-4: From Controller: To Keypad: Dimensions (HWD): Weight: •...

  • Page 9: Rack Mounting

    Rack Mounting Overview Tango units occupy two rack spaces in a standard 19" equipment rack. Rack mounting brackets and screws are located in the accessories box supplied with the unit. Exercise extreme care when lifting or moving Tango units within the rack to avoid injury.
  • Page 10 Rack Mounting Tango Amplifiers...

  • Page 11: Wiring And Connections

    This remarkable technology removes the need for control wire since the control and audio signals are shared on the same wire. The reliability and simplicity of this system has been proven for years. AMX Matrix Audio is the only company that offers a “retrofit solution”, one which allows the replacement of volume controls with AMX Matrix Audio keypads and Controllers, giving full control over the sources.

  • Page 12: Cabling Instructions

    The Tango Amplifier is cabled using standard 4-conductor speaker cable originating at the Tango Controller, passing through the Keypad, and terminating at the speaker location. AMX recommends using a bundled 4- conductor 16-gauge stranded copper wire in a single continuous run.

  • Page 13: Connecting To A Tango Audio Controller

    Connecting To a Tango Audio Controller Connect the Tango Amplifier to the Tango Audio Controller via the 4-pin connector labelled “From Controller” on the rear panel of the Amplifier. Connecting SWT Keypads Connect SWT Keypads (DAS-MET-6SRC or K-Series) to the Tango Amplifier via the SWT connector labelled “To Keypad”...
  • Page 14 Wiring and Connections Tango Amplifiers...
  • Page 15 Wiring and Connections Tango Amplifiers...
  • Page 16 It’s Your World - Take Control™ 3000 RESEARCH DRIVE, RICHARDSON, TX 75082 USA • 800.222.0193 • 469.624.8000 • 469-624-7153 fax • 800.932.6993 technical support • www.amx.com...

This manual is also suitable for:

Das-tamp8-sig

Table of Contents