Configuring Advanced Internet Access Point Settings; Ip Configuration Page; Proxies Page; Data Call Page - Nokia 9500 User Manual

C o n t r o l p a n e l
Password prompt — Change this to
•
not want to save your password to the device.
User name — Type a user name if required by the service provider. The user name may be needed to make a data
•
connection, and is usually provided by the service provider. The user name is often case-sensitive.
Password — A password may be needed to connect to the Internet, and is usually provided by the service provider. The
•
password is often case-sensitive.
4. After defining the settings, press
the setup wizard.

Configuring advanced Internet access point settings

Press Advanced when you have finished setting up the basic Internet access point settings. The pages and options available
depend on the connection type you have selected.

IP configuration page

Note that the two protocols (IPv4 and IPv6) require slightly different settings.
Network type (for GPRS only) — For a GPRS connection you must specify which protocol you want to use.
•
Auto retrieve IP — If you select Yes, the IP address is obtained automatically from the server. This setting is also called dynamic
•
IP address.
IP address — The IP address of the device. If the IP address is obtained automatically, you are not required to enter details
•
here.
Auto retrieve DNS — If you select
•
from the server. The respective value for the IPv6 protocol is
names such as www.nokia.com into IPv4 addresses like 192.100.124.195, or IPv6 addresses like 3ffe:
2650:a640:1c2:341:c39:14. If you select
addresses for the primary and secondary DNS servers.

Proxies page

You may want to use a proxy to quicken access to the Internet. Some Internet service providers require the use of Web proxies.
Contact your Internet service provider to determine proxy details.
If you have made an Internet connection to your company's intranet, and are unable to retrieve Web pages from the general
Internet, you may need to set up a proxy server to retrieve Web pages outside your company's intranet.
Define the following:
Proxy protocol — Select the protocol type of the proxy. You can set different proxy settings for each protocol.
•
Use proxy server — Select
•
Proxy server — Enter the IP address of the proxy server, or the domain name. Example domain names are: company.com and
•
organisation.org.
Port number — The number of the proxy port. The port number is related to the protocol. Common values are 8000 and 8080,
•
but vary with every proxy server.
No proxy for — Define the domains for which the HTTP or HTTPS proxy is not needed.
•

Data call page

Define the following:
Connection type — Define the GSM data call type. To use
•
necessary, activate it for your SIM card.
Remote modem type — Define whether the device uses an analog or digital connection. This setting depends on both your
•
GSM network operator and Internet service provider, because some GSM networks do not support certain types of ISDN
connections. For details, contact your Internet service provider. If ISDN connections are available, they establish connections
more quickly than analog methods.
Modem speed — This option allows you to limit the maximum connection speed. Higher data rates may cost more, depending
•
on the service provider. The speed represents the maximum speed at which your connection will operate. During the
connection, the operating speed may be less, depending on network conditions.
Modem initialisation — You can control your device using modem AT commands. If required, enter characters specified by
•
your service provider.

Script page

A script can automate the connection between the device and the server. Contact your Internet service provider to find out
whether you need a script.
Define the following:
Use login script — If you select Yes, you can write or import a login script. You can edit the script in the
•
Show terminal window
•
Copyright © 2004-2005 Nokia. All rights reserved.
Yes if you must write a new password every time you log on to a server, or if you do
Advanced to define advanced settings, if necessary. Otherwise, press
Yes for the IPv4 protocol, the DNS (domain name server) address is obtained automatically
No for the IPv4 protocol, or
Yes to use the proxy server.
— If you select Yes, once a connection is established, you see the execution of the script.
Well known. DNS is an Internet service that translates domain
Manual for the IPv6 protocol, you must specify the IP
High speed, the service provider must support this feature, and if
71
Finish or Done to exit
Login script field.