Set Up An Internet Access Point For Data Calls; Advanced Internet Access Point Settings For Data Calls; Set Up An Internet Access Point For Packet Data (Gprs) - Nokia E61i User Manual

C o n n e c t i v i t y

Set up an Internet access point for data calls

1. Select Menu Tools
>
2. Select Options New access
>
To start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
Dial-up number — Enter the modem telephone number of the access point. Use + before international numbers.
•
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
•
by your service provider.
Prompt password — Select
•
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
•
the service provider.
Authentication — Select
•
when possible.
Homepage — Enter the Web address of the page you want to display as a home page when you use this access point.
•
Data call type — Select
•
Max. data speed — Select the limit to apply to the transfer speed. If you select Automatic, the data transfer rate is
•
determined by the network and may be affected by network traffic. Some service providers may charge more for higher
data rates.
4. After defining the basic settings, select
settings and exit.

Advanced Internet access point settings for data calls

After setting up a basic Internet access point for
and define the following advanced settings.
IPv4 settings — Enter the device IP and name server addresses for IPv4 Internet protocol.
•
IPv6 settings — Enter the device IP and name server addresses for IPv6 Internet protocol.
•
Proxy serv. address — Enter the proxy server address.
•
Proxy port number — Enter the proxy server port number. Proxy servers are intermediate servers between a browsing service
•
and its users, which are used by some service providers. These servers may provide additional security and speed up access
to the service.
Use callback — Select Yes
•
Callback type — Select
•
Callback number — Enter your data call phone number of your device, which the callback server uses.
•
Use PPP compress. — Select
•
Use login script — Select Yes, if your Internet service provider requires a login script, or if you want to automate your login.
•
A login script is a sequence of instructions that the system follows during the login process.
Login script — Enter the login script. This setting is available only if you have selected
•
Modem initialization — Enter a command string for the connection setup, if required by your service provider.
•

Set up an Internet access point for packet data (GPRS)

When you switch the device on, it may recognize the SIM card provider and configure the correct text message, multimedia
message, and GPRS settings and access points automatically.
1. Select Menu Tools
>
2. Select Options New access
>
To start with an empty access point, select
3. Define the following settings.
Connection name — Enter a descriptive name for the connection.
•
Data bearer — Select
•
Access point name — Enter the name for the access point. The name is usually provided by your service provider or network
•
operator.
User name — Enter your user name if required by the service provider. User names are often case-sensitive and provided
•
by your service provider.
Prompt password — Select
•
device memory and automate the login.
Password — Enter your password if required by the service provider. The password is often case-sensitive provided by
•
the service provider.
© 2007 Nokia. All rights reserved.
Settings Connection
> >
point. To use an existing access point as a basis for the new one, select
Use default
Data call or High speed data (GSM
Yes to enter your password each time you log into a server or
Secure to always send your password encrypted or
Analog or ISDN.
Options
Data call
if you have a service that dials back to your device when you establish an Internet connection.
Use server no. or Use other
Yes to speed up the data transfer, if it is supported by the remote PPP server.
Settings Connection
> >
point. To use an existing access point as a basis for the new one, select
Use default
Packet data.
Yes to enter your password each time you log into a server or
Access points.
>
settings.
only).
Advanced settings to define the advanced settings or
>
or High speed data (GSM
no., according to instructions from your service provider.
Access points.
>
settings.
54
Use existing
No to save the password in your
Normal to send your password encrypted
only), select Options Advanced
>
Use login script > Yes.
Use existing
No to save the password in your
settings.
Back to save the
settings,
settings.