Table of Contents
Advertisement
<INITIAL SET UP/INFORMATION> (continued)
Setting (default: "OFF")
"OFF," "REMAIN," "WARNING," "ALARM"
SETTING
BUZZER
When reaching the remaining
capacity set in "REMAIN HDD"
When a failure occurs and
a warning is displayed
When an alarm recording or
emergency recording is started
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "BUZZER" in the <REAR
TERMINAL SETTINGS> screen. Display the desired setting
and determine such setting.
2. Press the CLEAR button or the SET UP button.
REMAIN HDD
This item is used to output a warning when the remaining
HDD capacity becomes low during recording. Set the HDD
and remaining capacity for this warning.
<REAR TERMINAL SETTINGS>
MODE OUT 1
MODE OUT 2
MODE OUT 3
MODE OUT 4
MODE OUT 5
KEY SOUND
BUZZER
>>REMAIN HDD
CALL OUT SETTINGS
EMERGENCY REC DURATION
A warning is output using the following methods
when the remaining capacity becomes low during
recording.
• The recorded capacity of HDD flashes when "3" is
set to "DISPLAY MODE" in the <TIME DATE/
DISPLAY SETTINGS> screen.
• A buzzer sounds when "REMAIN" is set to "BUZZER"
in the <REAR TERMINAL SETTINGS> screen.
Setting of HDD (default: "MAIN")
"MAIN": Displays a warning of low MAIN HDD capacity.
"SUB": Displays a warning of low SUB HDD capacity.
"OFF": Does not display a warning of low HDD ca-
pacity.
"SUB" appears when "HDD SETTING" in
<INITIALIZATION> screen is set to "PARTITION."
Setting of "REMAIN HDD" capacity (default: "10%")
"2%," "4%," "6%," "8%," "10%," "15%,""20%," "30%,"
"40%," "50%"
1. Press the SET UP button } <SETTINGS> } <INITIAL SET
UP/INFORMATION> } Select "REMAIN HDD" in the <REAR
TERMINAL SETTINGS> screen and then press the ENTER
button twice.
• The setting item of selecting HDD is highlighted when the
ENTER button is pressed once. When the button is pressed
again, the background turns red and flashes.
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
50
REMAIN
WARNING
ALARM
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
ON
OFF
MAIN-10%
10M
2. Press the JOG
,
buttons to display the desired HDD
and then press the ENTER button.
• The setting item is determined and flashing stops.
3. Press the JOG
button to highlight the REMAIN HDD
capacity and then press the ENTER button.
• The background of the setting item turns red and flashes.
4. Press the JOG
,
buttons to display the desired capacity
and then press the ENTER button.
• The setting item is determined and flashing stops.
5. Press the CLEAR button or the SET UP button.
CALL OUT SETTINGS
This menu is used to output warning signals from the MODE
OUT terminal which is set to "CALL OUT" in <REAR
TERMINAL SETTINGS> screen to the device connected
to that terminal.
<CALL OUT SETTINGS>
>>HDD MAIN REMAIN
HDD MAIN FULL
HDD SUB REMAIN
HDD SUB FULL
<CALL OUT SETTINGS> is available when any
of the MODE OUT 1 to 5 settings are set to "CALL
OUT."
"HDD SUB REMAIN" and "HDD SUB FULL"
appear when "HDD SETTING" in <INITIALIZATION>
screen is set to "PARTITION."
• HDD MAIN REMAIN/HDD SUB REMAIN
When reaching the specified remaining HDD capacity, a
signal is output from the MODE OUT terminal which is set
to "CALL OUT" in <REAR TERMINAL SETTINGS> screen
and "REC/REM" appears on the screen.
Setting (default: "OFF")
"2%," "4%," "6%," "8%," "10%," "15%,""20%," "30%,"
"40%," "50%," "OFF"
1. Press the SET UP button } <SETTINGS> } <INITIAL
SET UP/INFORMATION> } <REAR TERMINAL SETTINGS>
} Select "HDD MAIN REMAIN" or "HDD SUB REMAIN" in the
<CALL OUT SETTINGS> screen. Display the desired setting
and determined such setting.
2. Press the CLEAR button or the SET UP button.
By pressing and holding the WARNING RESET
button for more than 3 seconds, the HDD capacity
warning from the MODE OUT terminal which is set
to "CALL OUT" in <REAR TERMINAL SETTINGS>
screen can be cleared.
OFF
OFF
OFF
OFF
Advertisement
Table of Contents
