Page 2
All models are designed for use with either AC120V, 60Hz or AC240, 50Hz voltages. The unit will autoswitch to either of these voltages. 2. Do Not Touch The UNO-S2 With Wet Hands – Do not handle the unit or power cord when your hands are wet or damp. If tion.
Page 5
USER GUIDE UNO-S2 Keypad Front Panel LCD PANEL - 12-character backlit display shows status of the room, source, volume, and more SOURCE SELECT BUTTON - Scrolls through the sources directly connected to the CAV6.6. Press and hold brings up the USER MENU for Loudness, Bass, Treble, etc.
USER GUIDE UNO-S2 Keypad Normal Operation MODE: “DND”- Do Not Disturb “SHARED”- Same source selected in multiple rooms “SYS-ON”- Indicates system on “PARTY”- Party Mode enabled “MASTER”- Master Keypad in Party Mode 12-character display Volume Indicator Indicates the middle of setting range...
USER GUIDE UNO-S2 Keypad User Menu Zone On/Off Source Select Button Press and release to turn on the UNO scrolls through the six A/V source System Keypad. This also turns on the cor- inputs and the Aux source. To change responding CAV6.6’s room, and any pre-...
Page 8
USER GUIDE UNO-S2 Keypad User Menu The following keys are used to navigate button until SAVED is displayed on the and make changes while using the User LCD panel. Now a press and release of the Menu: button will recall the favorite preset. To set a...
USER GUIDE UNO-S2 Keypad Settings Feature and Setting: a Master Keypad (if enabled) but only one 1. BASS -10 < Bass:Flat > +10 Master Keypad may exist at a time in Party 2. TREBLE -10 < Treble:Flat > +10 Mode. Selecting Master Keypad mode from another keypad will transfer Master Keypad 3.
INSTALLER GUIDE UNO-S2 Keypad Update Port DATA RS-232 DATA RS-232 SETUP BUTTON - Activates Installer Setup Mode for the UNO-S2 keypad OS UPDATE PORT - Port used for UNO keypad OS software updates...
EXTERNAL IR RECEIVER IN CONNECTOR - Connection for an external IR Receiver. OS UPDATE JUMPER - Selects “Run” or “OS Update” mode. RESET BUTTON - Reset whenever changing from RUN to OS update 110 PUNCHDOWN CONNECTOR - Termination for CAT-5 connection between the UNO-S2 Keypad and the CAV6.6 controller.
INSTALLER GUIDE UNO-S2 Keypad Location The best infrared remote performance is double-gang electrical box. achieved with the keypad installed away Route CAT-5 wire to the junction box from from any direct sunlight, plasma TV, and low the CAV6.6. voltage lighting controls. Also consider con- Use the supplied 110 punchdown tool to venience when choosing a location.
INSTALLER GUIDE UNO-S2 Keypad Connections Punchdown Tool Jumper Setting (back of keypad) CAT-5 Connections (back of keypad) Punchdown Tool OS Update Port (front of keypad)
INSTALLER GUIDE UNO-S2 Keypad Connections CAT-5 Connection OS Update Port The UNO-S2 Keypad uses a 110-punch- The OS Update Port is is used to update the down terminal to provide a simple installa- UNO-S2 Keypad operating system software tion and strong connection for CAT-5 in the future.
IR Receiver Connection Back of UNO-S2 Back of Russound 858 The UNO-S2 keypad has an EXTERNAL IR RECEIVER IN terminal for connecting an external IR Receiver such as the Russound 858, SaphIR Eye, or SaphIR Phantom. Use 2 twisted pair wire with...
The Russound UNO-S2 is fully guaranteed against all defects in materials and workman- ship for two (2) years from the date of purchase. During this period, Russound will replace any defective parts and correct any defect in workmanship without charge for either parts or labor.
Page 19
In these cases, repairs will be made on the basis or the retail value of the parts and labor. To return for repairs, the unit must be shipped to Russound at the owner's expense, along with a note explaining the nature of service required. Be sure to pack the unit in a corrugated container with at least three (3) inches of resilient material to protect the unit from damage in transit.