Refrigerator Care - Whirlpool Refrigerator User Instructions

Water Filtration System
Do not use with water that is microbiologically unsafe or
of unknown quality without adequate disinfection before
or after the system. Systems certified for cyst reduction
may be used on disinfected waters that may contain
filterable cysts.
Water Filter Status Light
The water filter status light will help you know when to change
your water filter.
When the dispenser control panel's water filter status display
changes to "ORDER," this tells you that it is almost time to
change the water filter cartridge.
Replace the water filter cartridge when the water filter status
display changes to "REPLACE."
If water flow to your water dispenser or ice maker decreases
noticeably, change the filter sooner. The filter should be replaced
at least every 6 months, depending on your water quality and
usage.
After changing the water filter, reset the status light by
pressing and holding the FILTER button for 3 seconds. When
the system is reset, the "ORDER" and "REPLACE" icons will
disappear from the display screen.
Cleaning
WARNING
Explosion Hazard
Use nonflammable cleaner.
Failure to do so can result in death, explosion, or fire.
Both the refrigerator and freezer sections defrost automatically.
However, clean both sections about once a month to avoid
buildup of odors. Wipe up spills immediately.
IMPORTANT: Because air circulates between both sections, any
odors formed in one section will transfer to the other. You must
thoroughly clean both sections to eliminate odors. To avoid odor
transfer and drying out of food, wrap or cover foods tightly.
To Clean Your Refrigerator:
NOTE: Do not use abrasive or harsh cleaners such as window
sprays, scouring cleansers, flammable fluids, cleaning waxes,
concentrated detergents, bleaches or cleansers containing
petroleum products on plastic parts, interior and door liners or
gaskets. Do not use paper towels, scouring pads, or other harsh
cleaning tools.
1. Unplug refrigerator or disconnect power.
2. Hand wash, rinse, and dry removable parts and interior
surfaces thoroughly. Use a clean sponge or soft cloth and a
mild detergent in warm water.
Changing the Water Filter
1. Locate the water filter in the top-right corner of the refrigerator
2. Lift open the filter cover door. The filter will be released and
3. When the door is completely open, pull the filter straight out.
4. Take the new filter out of its packaging and remove the covers
5. With the arrow pointing up, align the new filter with the filter
6. Close the filter cover door completely in order to snap the filter
7. Flush the water system. See "Water and Ice Dispensers."

REFRIGERATOR CARE

3. Wash stainless steel and painted metal exteriors with a clean
4. There is no need for routine condenser cleaning in normal
5. Plug in refrigerator or reconnect power.
NOTE: Not all bulbs will fit your refrigerator. Be sure to replace the
bulb with one of the same size, shape and wattage.
1. Unplug refrigerator or disconnect power.
2. Remove light shield when applicable.
3. Remove light bulb and replace with one of the same size,
4. Replace light shield when applicable.
5. Plug in refrigerator or reconnect power.
compartment.
then eject as the door is opened.
NOTE: There may be some water in the filter. Some spilling
may occur. Use a towel to wipe up any spills.
from the O-rings. Be sure the O-rings are still in place after the
covers are removed.
housing and slide it into place. The filter cover door will
automatically begin to close as the new filter is inserted.
into place. You may need to press hard.
sponge or soft cloth and a mild detergent in warm water.
home operating environments. If the environment is
particularly greasy or dusty, or there is significant pet traffic in
the home, the condenser should be cleaned every 2 to
3 months to ensure maximum efficiency.
If you need to clean the condenser:
Remove the base grille. See the "Door Removal"
instructions, either in the User Instructions or the separate
instruction sheet provided with your refrigerator.
Use a vacuum cleaner with a soft brush to clean the grille,
the open areas behind the grille and the front surface area
of the condenser.
Replace the base grille when finished.
Changing the Light Bulbs
The dispenser lights are LEDs that cannot be changed.
On some models, the interior lights are LEDs that cannot
be changed.
On some models, the interior lights require a 40-watt bulb.
NOTE: To clean the light shield, wash it with warm water and
liquid detergent. Rinse and dry the shield well.
shape and wattage.
15