Other Function; Tv Auto On/Off Function; Attenuation To Analog Input Signal; Listening Through Headphones - Marantz SR5600 User Manual

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to
the TV-VIDEO in jack to control the power (ON/
OFF) to the SR5600.
AUTO POWER ON
1.
Be sure the TV auto mode is ENABLED.
(Refer page 19 : System Setup)
2.
Connect your TV TUNER (etc) to the TV-
VIDEO in terminal. Be sure to connect the
VIDEO input.
3.
Turn OFF the power to the TV TUNER and the
SR5600.
4.
Turn ON the TV TUNER and tune in a
receivable station.
5.
When the station is received, the SR5600
turns ON and TV is selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER
OFF or select a channel that does not contain
any broadcast.
2.
The power to the SR5600 switches to
STANDBY after approx. 5 minutes.
Notes:
• AUTO POWER OFF is canceled if the SR5600 is
set to a source other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO
FUNCTION to turn ON.
• The S-Video terminal does not support "TV
AUTO ON/OFF" function.
ATTENUATION TO ANALOG INPUT
SIGNAL
T-MODE RDS F.DIRECT
INPUT/DISC+ AUDIO SUB-T/ATT PTY
CH.SEL LIP.SYNC
SYSTEM REMOTE CONTROLLER
RC5500SR
If the selected analog audio input signal is greater
than the capable level of internal processing, the
"PEAK" indicator will light up on the front display.
If this happens, you should press the ATT button
on the remote.
"ATT" indicator will be illuminated when this
function is activated. The signal-input level is
reduced by about half. Attenuation will not work
with the output signal of TAPE-OUT, CD-R/MD-
OUT, VCR1-OUT and DSS/VCR2-OUT.
This function is memorized for each individual
input source.

LISTENING THROUGH HEADPHONES

This jack may be used to listen to the SR5600's
output through a pair of headphones. Be certain
that the headphones have a standard 1/4" stereo
p h o n o p l u g . ( N o t e t h a t t h e s p e a k e r s w i l l
automatically be turned off when the headphone
jack is in use.)
AV SURROUND RECEIVER SR5600
INPUT SELECTOR
SURROUND PURE
MODE DIRECT
MULTI M. SPEAKER B
STANDBY
AUTO HT-EQ
POWER ON/OFF PHONES
Note:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.

DOLBY HEADPHONE MODE

This feature simulates the waveforms of the actual
sounds heard from the speakers.
When headphones are used, the MENU button
automatically switches to the Dolby headphone
mode.
The OSD that appears when the MENU button is
pressed is shown below.
HEAD PHONE
DOLBY HP MODE : BYPASS
: ✽✽✽
SURROUND
L LEVEL : 0dB
R LEVEL : 0dB
DOLDBY HP (Headphone) MODE can be selected
with the left and right cursor buttons.
→ → → →
BYPASS : Bypasses the Dolby headphone mode
and delivers ordinary 2-channel stereo.
DH1 : The size of a typical living room space
is simulated.
DH2 : The expansiveness of a structure as
large as a music hall is simulated.
DH3 : A large space such as that found in a
movie theater is simulated.
When the PURE DIRECT mode is selected, Dolby
surround processing is bypassed and "✽✽✽" is
displayed as the mode indication.
DISP MULTI AUTO TUNED ST V – O
SLEEP AUTO SURR DIRECT DISC 6.1
The surround mode can be selected when any of
the modes in DH1, DH2, or DH3 is selected.
SIMPLE
SETUP
L/R LEVEL can be set in the ±10 dB range.
MENU
Notes:
• The surround mode returns to the previous setting
as soon as the plug is removed from the jack.
• TONE cannot be set when any of the modes in
DH1, DH2, or DH3 is selected.
• The Dolby Headphone function will not work
when 32 or 96 kHz PCM digital signals are input.

VIDEO ON/OFF

When no video signal is connected to the SR5600
or a DVD, etc., is connected directly to your TV, the
unnecessary video circuit can be turned off by
selecting the "VIDEO OFF" setting.
To select video off, press the AMP button and
press the V-OFF button.
TUNER CD TAPE
AUX1 AMP
R5600
TV
VOL. SLEEP MUTE
SURROUND
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 EQ
L C R
AAC PCM LFE
SL S SR
OSD MENU
SURROUND PURE SIMPLE
MODE DIRECT SETUP DISPLAY MEMORY CLEAR
NIGHT CSII EX/ES
ENTER
4 5
AUTO HT-EQ MENU EXIT BAND T-MODE
DISPLAY MCH-ST STEREO
7 8
CLEAR MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
BASS TREBLE
TUNE/SEARCH

DISPLAY MODE

SET UP/
MENU OFF
T.TONE
PURE DIRECT AUTO
SR5600
1 2
NIGHT CSII EX/ES
4 5
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ATT ANALOG SURROUND
DIGITAL DIGITAL
SLEEP AUTO SURR DIRECT DISC 6.1 MT X 6.1 EQ
L C R
DISPLAY MCH-ST STEREO
AAC PCM LFE
SL S SR
7 8
CLEAR MEMO A/D P.SCAN/V-OFF
0
SURROUND PURE SIMPLE
MODE DIRECT SETUP DISPLAY MEMORY CLEAR
CHANNEL/SKIP
ENTER
AUTO HT-EQ MENU EXIT BAND T-MODE
BASS TREBLE TUNE/SEARCH
T-MODE RDS
You can select the display mode for the front
display of the SR5600.
To select this mode, press the DISPLAY on the
remote control.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display
Off → Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if
you make a change to the unit such as input or
surround mode, the display will show that change,
then go back to off after about 3 seconds. When
changing the volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
• Only the DISP indicator will be illuminated on the
front display in display off condition
CDR/MD
MAIN
VOL.
VIRTUAL
6
7.1CH IN
9
DTS
3
VIRTUAL
6
7.1CH IN
9
F.DIRECT
27