Advanced Connecting; Connecting The Remote Control Jacks - Marantz SR5600 User Manual

ADVANCED CONNECTING

DVD AUDIO PLAYER
or
SACD MULTI CHANNEL
COMPONENT VIDEO
PLAYER
INPUT-1
C B / C R /
P P Y
B R
S-VIDEO
R
TV DVD
MULTI
RC-5
RC
C
CENTER
L
TAPE CDR/MD
R
FRONT SURR. SURR. SUB
BACK WOOFER
IN OUT IN
AUDIO
R L R L R L
CONNECTING MULTI CHANNEL AUDIO SOURCE
The 7.1CH INPUT jacks are for multichannel
audio source such as a SACD multichannel
player, DVD audio player or external decoder.
If you use these jacks, switch on the 7.1CH INPUT
and set the 7.1CH INPUT level by using the
SETUP MAIN MENU. See page 28.
14
R L R L R L
R L R L
INPUT-2 MONITOR OUT
C B / C R / C B / C R /
P P Y P P
B R B R
L
VCR1 DSS/VCR2
MONITOR
IN OUT IN OUT OUT
R
FRONT SURR.
L L SL SL SBL SBL C C
IN
PRE PRE
POWER
OUT OUT
AMPLIFER
OUT
R R SR SR SBR SBR SW SW
MULTI L L SL SL SBL SBL C C
Subwoofer
7.1CH 7.1CH
IN IN
OUT OUT R R SR SR SBR SBR SW SW
(AUX2)
L R L R L R
Front
Left
Surround
Left
Surround
Back Left
CONNECTING AN EXTERNAL POWER AMPLIFIER
The PREOUT jacks are for connecting external
power amplifiers.
Be sure to connect each speaker to the corresponding
external power amplifier.

CONNECTING THE REMOTE CONTROL JACKS

ANTENNA
FM (75Ω)
GND AM
VIDEO
TV DVD VCR1 DSS/VCR2
IN OUT IN
R L DIGITAL IN DIGITAL OUT
3 4 COAX.
1 2 OPT.
TV DVD VCR1 DSS/VCR2
CENTER
L
R
IN OUT IN
SURR. SUB
BACK WOOFER
REMOTE
CD RECORDER
CONTROL
IN
OUT
Front
Center
EXTERNAL INTERNAL
Right
Surround
Right
Surround
Back Right
q
You can control other Marantz products through
this unit with the remote control by connecting the
REMOTE CONTROL terminals on each unit.
The signal transmitted from the remote control is
received by the remote sensor on this unit. Then
the signal is sent to the connected device through
this terminal. Therefore you need to aim the
remote signal only to the unit. Also, if a Marantz
power amplifier (some models excluded) is
connected to one of these terminals, the power
amplifier's, power switch is synchronized with this
unit's power switch.
Set the REMOTE CONTROL SWITCH on the units,
other than the main unit to EXT.(EXTERNAL) for
this feature.
COMPONENT VIDEO
INPUT-1 INPUT-2 MONITOR OUT
C B / C R / C B / C R / C B / C R /
Y P P Y P P Y P P
B R B R B R
S-VIDEO
VCR1 DSS/VCR2
MONITOR
MONITOR
TV DVD IN OUT IN OUT OUT
OUT OUT
2
MULTI
RC-5 RC-5
RC L SL SBL C
IN IN
RS-232C
PRE
OUT
OUT OUT
R SR SBR SW
CD TAPE CDR/MD MULTI L SL SBL C
7.1CH
IN
OUT IN OUT IN OUT OUT R SR SBR SW
(AUX2)
AUDIO
1
MD DECK
REMOTE
CONTROL
IN
OUT
EXTERNAL INTERNAL
w
Whenever external infrared sensors or similar
devices are connected to RC-5 IN of the SR5600,
be sure to always disable operation of the infrared
sensor on the main unit by using the following
procedure.
1.
Hold down the MULTI button and MENU
button on the front panel at the same time for
five seconds.
2.
The setting "IR=ENABLE" is shown on the FL
DISPLAY.
3.
Press the
to "IR=DISABLE".
4.
Press the ENTER button. Once this setting is
made, the infrared sensor on the main unit is
disabled.
Note:
• Be sure to set to "IR=ENABLE" when external
infrared sensors or similar devices are not
connected. Otherwise, the main unit will be
unable to receive remote control commands.
5.
To restore the original setting, perform steps 1
to 4 to set to "IR=ENABLE".
RC OUT
OPTION
REMOTE CD PLAYER
CONTROL
IN
OUT
EXTERNAL INTERNAL
or cursor button to change this