Other Function; Tv Auto On/Off Function; Attenuation To Analog Input Signal; Listening Over Headphones - Marantz SR9200 User Manual

OTHER FUNCTION

TV AUTO ON/OFF FUNCTION

This function allows the component connected to the TV-VIDEO in
jack to control the power (ON/OFF) to the SR9200.
AUTO POWER ON
1.
Be sure TV auto mode is ENABLE. (Refer page 31 : System
Setup)
2.
Connect your TV TUNER (etc) to the TV-VIDEO in terminal. Be
sure to connect the VIDEO input.
3.
Turn OFF the power to the TV TUNER and the SR9200.
4.
Turn ON the TV TUNER and tune in a receivable station.
5.
When the station is received, the SR9200 turns ON and TV is
selected automatically.
AUTO POWER OFF
1.
In the above situation, turn the TV TUNER OFF or select a
channel that does not contain any broadcast.
2.
The power to the SR9200 switches to STANDBY after approx. 5
minutes.
Notes:
• AUTO POWER OFF is canceled if the SR9200 is set to a source
other than TV.
The function reactivates when TV is selected again.
• Some TV broadcasts may cause the TV AUTO FUNCTION to
turn ON.
• S-Video terminal does not support "TV AUTO ON/OFF" function.

ATTENUATION TO ANALOG INPUT SIGNAL

PLAY CLEAR MEMO DOWN GYRO TUNING UP F/P AUTO-TUNE T-MODE
DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R TUNER
MULTI-SPK SLEEP S-DIRECT AUX1
AUX1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
MULTI ROOM A/D 7.1CH-IN AUX2
If the selected analog audio input signal is greater than the capable
level of internal processing, "PEAK" indicator will light up on the front
display. If this happens, you should press the ATT button or tap ATT
on the remote.
"ATT" indicator will light up when this function is activated. The signal-
input level is reduced by about the half. Attenuation will not work with
the output signal of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT, VCR2-
OUT and MULTI ROOM OUT.
This function is memorized for each individual input source.

LISTENING OVER HEADPHONES

This jack may be used to listen to the SR9200's output through a pair
of headphones. Be certain that the headphones have a standard 1/4"
stereo phone plug. (Note that the main room speakers will
automatically be turned off when the headphone jack is in use.)
Notes:
• When using headphones, the surround mode will automatically
change to STEREO.
• The surround mode returns to the previous setting as soon as the
plug is removed from the jack.
40
VOLUME
DOWN UP
MUTE ATT
DISPLAY CLEAR MEMO DOWN
SELECT ENTER LD DVD DSS TV VCR 1
MULTI-SPK SLEEP S-DIRECT AUX1
STANDBY
POWER ON/STANDBY PHONES MULTI ROOM A/D 7.1CH-IN AUX2

VIDEO ON/OFF

When no video signals of a DVD, etc., are connected to the SR9200 or
the DVD, etc., are connected directly to a TV, the unnecessary video
circuit can be turned off by selecting the "VIDEO OFF" setting.
To select video off condition, tap Video off on the remote.
Notes that VIDEO OFF will not work with the output signal of VCR1-
OUT and VCR2-OUT and MULTI ROOM OUT.

DISPLAY MODE

SELECTOR
SELECT
STANDBY
POWER ON/STANDBY
You can select the display mode for the front display of the SR9200.
To select this mode, press DISP button on the front panel or tap
Display on the remote control unit.
When this button is pressed, the display mode is switched in the
following sequence.
→ Auto-display Off → Display Off → Normal → Auto-display Off ....
In Auto display off mode, turn the display on automatically, after that
any condition of SR9200 is changed.
In Display off mode, turn the display off completely.
Notes:
• Only Disp will light up on the front display in display off
condition
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
SELECTOR
SELECT
STANDBY
POWER ON/STANDBY
If you have already assign any digital input to input source.
You can select temporarily the audio input mode for each input source
with A/D button on the remote controller or front panel.
GYRO TUN
When this button is pressed, the input mode is switched in the
V following sequence.
→ Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input to the digital and
analog input jacks for the selected input source are detected
automatically.
If no digital signal is being input, the analog input jacks are selected
automatically.
In Digital mode, input is fixed to an assigned digital input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporarily, so the result will not be stored in memory.
If you need to change input mode completely, use SYSTEM SETUP in
OSD menu system. (see page 29)
DISPLAY CLEAR MEMO F/P AUTO-TUNE T-MO
DOWN GYRO TUNING UP
ENTER
LD DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R
MULTI-SPK SLEEP S-DIRECT AUX1
AUX1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
MULTI ROOM A/D 7.1CH-IN AUX2
PHONES
DISPLAY CLEAR MEMO F/P AUTO-TUNE T-MO
DOWN GYRO TUNING UP
ENTER
LD DVD DSS TV VCR 1 VCR2/DVD-R CD TAPE CD-R
MULTI-SPK SLEEP S-DIRECT AUX1
AUX1 INPUT
DIGITAL S-VIDEO VIDEO L AUDIO R
MULTI ROOM A/D 7.1CH-IN AUX2
PHONES