Operation Of Remote Control Unit; General Information Of Rc5500Sr To Sr5600 - Marantz SR5600 User Manual

OPERATION OF REMOTE CONTROL
UNIT
REMOTE CONTROL
The distance between the transmitter of the
remote control and the IR SENSOR of the SR5600
should be less than 5 meters. If the remote control
is pointed in a direction other than the IR SENSOR
or if there is an obstacle between them, use of the
remote control may not be possible.
Remote-controllable range
SR5600
INPU
SELE T CTOR AV SURR
OUND RECE
SR550 IVER
0
MULT
I
STANDBY
POWE
ON/OF R SPEA M. KER
F B
MODE SURR OUND
PHON ES PURE
DIREC T
SIMPL
AUTO SETUP E
HT-EQ
MENU VOLUM
ENTER DISPL AY E
MEMO RY DOWN
EXIT CLEA
R
BAND
T-MOD E MUTE
UP
7.1CH
S-VIDE INPUT
O VIDEO AUX
1 INPUT
L AUDIO
R
60°
Remote control unit (RC5500SR)
LOADING BATTERIES
The life of the batteries used with the remote
control is about 4 months with normal use. Also be
sure to replace batteries earlier when you notice
that they are getting weak.
1.
Remove the back cover.
2.
Insert the new batteries (AAA type) with
correct and polarity.
3.
Close the cover until it clicks.
Notes:
• Do not mix alkaline and manganese batteries.
• Do not mix old and new batteries.
CAUTIONS ON BATTERIES
• Use "AAA" type batteries in this remote control
unit.
• If the remote control unit does not operate from
close to the main unit, replace the batteries with
new ones, even if less then a year has passed.
• The included battery is only for verifying
operation. Replace it with a new battery as soon
as possible.
• When inserting the batteries, be careful to do so
in the proper direction, following the + and -
marks in the remote control unit's battery
compartment.
• To prevent damage or battery fluid leakage:
- Do not use a new battery with an old one.
- Do not use two different types of batteries.
- Do not short-circuit, disassemble, heat or
dispose of batteries in flames.
• Remove the batteries when not planning to use
the remote control unit for a long period of time.
• If the batteries should leak, carefully wipe off the
fluid from the inside of the battery compartment,
then insert new batteries.
• When disposing of used batteries, please
comply with governmental regulations or
environmental public instruction's rules that
apply in your country or area.

GENERAL INFORMATION OF RC5500SR TO SR5600

To control the SR5600 by your RC5500SR, you have to select the device AMP or TUNER by pressing the
function selector button. Please refer below for the details in AMP and TUNER mode.
AMP MODE
POWER
Function selector * Selects a particular source component
POWER
SLEEP *
TV VCR1 DSS/VCR2 DVD MUTE *
TUNER CD TAPE CDR/MD
VOL 34 *
AUX1 AMP
MENU
TV MAIN
VOL. SLEEP MUTE VOL.
Cursor
OSD MENU
ENTER
ENTER
SET UP/
MENU OFF
T.TONE SETUP/T.TONE Enters the test tone mode for setting the Speaker Level Setup
PURE DIRECT AUTO DTS
1 2 3
NIGHT CSII EX/ES VIRTUAL
MENU OFF
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
7 8 9
PURE DIRECT * Selects the Pure Direct mode
CLEAR MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
NIGHT *
BASS TREBLE TUNE/SEARCH
DISPLAY *
T-MODE RDS F.DIRECT
Surround mode (1-8) Selects the surround mode
INPUT/DISC+ AUDIO SUB-T/ATT PTY
CH.SEL LIP.SYNC
7.1CH-IN (9)
SYSTEM REMOTE CONTROLLER
RC5500SR
A/D (0)
BASS 34 *
TREBLE 34 *
SUB-T/ATT
P.SCAN/V-OFF
CH. SEL
TUNER MODE
LIP.SYNC
* These buttons are used to control SR5600 in any function mode.
POWER
TV VCR1 DSS/VCR2 DVD
TUNER
TUNER CD TAPE CDR/MD
0-9
AUX1 AMP
TV MAIN
VOL. SLEEP MUTE VOL.
CLEAR
OSD MENU MEMO
P.SCAN/V-OFF
ENTER
CHANNEL/SKIP • Selects a preset station
SET UP/
MENU OFF
T.TONE
PURE DIRECT AUTO DTS
1 2 3
/
4 ¢
NIGHT CSII EX/ES VIRTUAL
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
TUNE/SEARCH
7 8 9
CLEAR MEMO A/D P.SCAN/V-OFF
5 / 6
0
CHANNEL/SKIP
T-MODE 1 2
BASS TREBLE TUNE/SEARCH
T-MODE RDS F.DIRECT
RDS ;
INPUT/DISC+ AUDIO SUB-T/ATT PTY
F.DIRECT 2
CH.SEL LIP.SYNC
PTY 9
SYSTEM REMOTE CONTROLLER
RC5500SR
* : European model only
Turns the SR5600 on and off
Sets the sleep timer function
Decreases the sound temporarily
Adjusts the over all sound level
Enters the SETUP MENU
Moves the cursor for settings in the SETUP MENU
• Enters the SETUP MENU
• Confirms the settings in SETUP MENU
Exits from the SETUP MENU
Turns on or off the NIGHT mode
Change the front display mode
Selects the 7.1CH IN
Switches between the analog and digital inputs
Adjusts the tone control of low frequency sound
Adjusts the tone control of high frequency sound
Reduces the input level
Turns on or off the Video output
Adjusts the input level
Selects the LIP. SYNC mode
Selects a frequency band
Inputs the numeric #s
Clears the inputting
Enters the tuner preset memory numbers
Starts preset scan
• Changes a PTY type *
Tunes a station
Selects the auto stereo mode or mono mode
Selects the display mode in RDS *
Selects the "Frequency direct input"
Displays the programmed information of the current station *
9