Rear Panel - Marantz SR5600 User Manual

REAR PANEL

q w e r
ANTENNA COMPONENT VIDEO
INPUT-1 INPUT-2
C C C
Y B / R / Y B /
P B P R P B
FM (75Ω) GND AM
VIDEO S-VIDEO
VCR1
TV DVD VCR1 DSS/VCR2 MONITOR
TV DVD IN
IN OUT IN OUT OUT
MULTI
RC-5
DIGITAL IN DIGITAL OUT RC
IN
3 4 COAX.
RS-232C
1 2 OPT.
OUT
TV DVD VCR1 DSS/VCR2 CD TAPE CDR/MD
L
R
IN OUT IN OUT IN OUT IN OUT
AUDIO
!6 !5 !4 !3 !2
q
VIDEO IN/OUT (TV, DVD, VCR1, DSS/VCR2)
These are the video inputs and outputs. There are
4 video inputs and 2 video outputs and each one
includes both composite video and S-video
configurations. Connect VCRs, DVD players, and
other video components to the video inputs.
The 2 video output channels can be used to be
connected to video tape recorders for making
recordings.
The input signals of video and S-video are
converted each other, and each of the converted
video signals can be output.
w
FM antenna terminal (75 ohms)
Connect an external FM antenna with a coaxial
cable, or a cable network FM source.
AM antenna and ground terminals
Connect the supplied AM loop antenna. Use the
terminals marked "AM" and "GND". The supplied
AM loop antenna will provide good AM reception in
most areas. Position the loop antenna until you
hear the best reception.
e
RS-232C
The RS-232C port is to be used in conjunction with
an external controller to control the operation of the
SR5600 by using an external device.
6
t y u
MODEL NO.SR5600
MONITOR OUT
C C C
R / Y B / R /
P R P B P R
DSS/VCR2 MONITOR
OUT IN OUT OUT
L SL SBL C
AC IN
PRE
OUT
R SR SBR SW
MULTI L SL SBL C
R L R L
7.1CH
IN
FRONT CENTER SURROUND
SPEAKER SYSTEMS : 6-8 OHMS
OUT R SR SBR SW
(AUX2)
!1 !0 o
r
COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to
these component video connectors on the
SR5600. The SR5600 has two component video
input connectors to obtain the color information (Y,
C , C ) directly from the recorded DVD signal or
B R
other video component and one component video
output connector to output it directly into the matrix
decoder of the display device.
By sending the pure DVD component video signal
directly, the DVD signal forgoes the extra
processing that normally would degrade the
image. The result is vastly increased image
quality, with incredibly life like colors and crisp
detail.
When the video convert function is enabled, video
and S-video images can be output to the
COMPONENT MOINTOR OUT jack.
t
MONITOR OUT
This is a monitor output and each one includes
both composite video and S-video configurations.
W h e n c o n n e c t i n g t w o v i d e o m o n i t o r s o r
televisions, be aware that the OSD interface can
be used with both MONITOR OUT connections.
y
Preamp Outputs
(L, R, SL, SR, SBL, SBR, C)
Jacks for L(front left), R (front right), C (Center), SL
(surround left), SR (surround right), SBL (surround
i
back left) and SBR (surround back right).
Use these jacks for connection to external power
amplifiers.
u
AC INLET
Plug the supplied power cord into this AC INLET
and then into the power outlet on the wall.
SR5600 can be powered by 230V AC only.
AC OUTLET
SWITCHED
100W MAX.
i
AC OUTLETS
Connect the AC power cable of component such
as a DVD or CD player to this outlet.
R L
The marked SWITCHED provides power only
when the SR5600 is turned on and is useful for
SURROUND BACK
M.SPEAKER B
components which you use every time you play
your system.
Caution:
• In order to avoid potential turn-off thumps,
anything plugged into these outlets should be
powered up before the SR5600 is turned on.
• The capacity of this AC outlet is 100W. Do not
connect devices that consume electricity more
than the capacity of these AC outlet. If the total
power consumption of the connected devices
exceeds the capacity, the protection circuit shuts
down the power supply.
o
Speaker outputs terminals
Seven terminals are provided for the front left, front
right, front center, surround left, surround right,
surround back left and surround back right
speakers.
Note:
• You can use surround back speaker terminals as
M (Multiroom) SPEAKER B terminals, when you
use no surround back speaker.
!0
Subwoofer Output
Connect this jack to the line level input of a
powered subwoofer. If an external subwoofer
amplifier is used, connect this jack to the
subwoofer amplifier input. If you are using two
subwoofers, either powered or with a 2 channel
subwoofer amplifier, connect a "Y" connector to
the subwoofer output jack and run one cable from
it to each subwoofer amplifier.
!1
7.1 CHANNEL or AUX2 INPUT
By connecting a DVD Audio player, SACD
multichannel player, or other components that has
a multichannel port, you can playback the audio
with 5.1 channel or 7.1 channel outputs.
!2
Multiroom Outputs (Audio L&R)
These are the audio output jacks for the Multi zone
(Multi room).
Connect these jacks to optional audio power
amplifiers to listen the source selected by the
multiroom system in a remote room.
!3
MULTI ROOM REMOTE IN/OUT terminals
IN: Connect to a multi-room remote control
device, available from your Marantz dealer.
OUT: Connect to the Marantz component
equipped with remote control (RC-5)
terminals in Multi zone (Multi room).
!4
REMOTE CONT. IN/OUT terminals
Connect to a Marantz component equipped with
remote control (RC-5) terminals.
!5
AUDIO IN/OUT (CD, TAPE, CD-R, TV,
DVD, VCR1, DSS/VCR2)
These are the analog audio inputs and outputs.
There are 7 audio inputs (4 of which are linked to
video inputs) and 4 audio outputs (2 of which are
linked to video outputs). The audio jacks are
nominally labeled for cassette tape decks,
compact disc players, DVD players and etc.... The
audio inputs and outputs require RCA-type
connectors.
!6
DIGITAL INPUT (Dig.1 - 4) / OUTPUT
(coaxial, optical)
These are the digital audio inputs and outputs.
There are 2 digital inputs with coaxial jacks, 2 with
optical jacks.
The inputs accept digital audio signals from a
compact disc, LD, DVD, or other digital source
component.
For digital output, there is 1 coaxial output and 1
optical output.
The digital outputs can be connected to MD
recorders, CD recorders, DAT decks, or other
similar components.