Programming The Remote Controller - Marantz SR5600 User Manual

¤1
PURE DIRECT button
When this button is pressed, the tone control
circuit is bypassed.
¤2
SETUP / T.TONE button
(when AMP mode is selected)
Used to enter the test tone menu.
¤3
OSD button
(when AMP mode is selected)
When this button is pressed, the current setting is
displayed on the TV monitor.
¤4
SLEEP (sleep timer) button
This button is used for setting the sleep timer. It
can be operated the same way as the button on the
unit.
¤5
TV VOLUME UP ( ) /DOWN ( ) buttons
These buttons increase or decrease TV's volume.
8
PROGRAMMING THE REMOTE
CONTROLLER
The remote controller RC5500SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-
digit code or by scanning the codes until the
correct one is found. We recommend to using the
4-digit code. This mode is faster and more reliable.
The code scanning method should be used only if
you cannot find the code for one of your
appliances. The codes are listed at the end of this
book.
Important:
• Use the remote control buttons for programming,
not the buttons of the receiver or other appliances.
• Some codes may be not match your equipment.
In this case, your equipment cannot be controlled
with this remote controller.
PROGRAMMING WITH THE 4-DIGIT CODE
ENTER
POWER SET UP/
MENU OFF
1. T.TONE
PURE DIRECT AUTO
1 2
NIGHT CSII EX/ES
TV VCR1 DSS/VCR2 DVD
4 5
DISPLAY MCH-ST STEREO
1.
TUNER CD TAPE CDR/MD 7 8
CLEAR MEMO A/D P.SCAN/V-OFF
0
AUX1 AMP 2. CHANNEL/SKIP
TV MAIN
VOL. VOL.
SLEEP MUTE
BASS TREBLE
TUNE/SEARCH
T-MODE RDS
OSD MENU
INPUT/DISC+ AUDIO SUB-T/ATT
1.
Press and hold down the Function Selector
button for the appliance which should be
controlled and press SETUP button until the
indicator blinks twice.
2.
Press the 4-digit code for appliance (code
table at the end of this book)
3.
When the procedure is successful, the indicator
will blink twice.
Note:
• If the indicator did not blink twice, then repeat
steps 1 through 2 and try entering the same code
again.
SCANNING THE CODE TABLE
4.
POWER
2.
TV VCR1 DSS/VCR2 DVD
2.
PURE DIRECT
6.
TUNER CD TAPE CDR/MD
4.
AUX1 AMP
3.
TV MAIN
VOL. SLEEP MUTE VOL.
OSD MENU
1.
Switch on the appliance which should be
controlled.
2.
Press and hold down the Function Selector
button for appliance which should be
controlled and press SETUP button until the
indicator blinking twice.
3.
Press the code 9 - 9 - 1.
The indicator will blink twice.
4.
Aim the remote control at the appliance and
slowly alternate between pressing POWER
button and the Function Selector button for
the appliance.
5.
Stop when the appliance turns off.
6.
Press SETUP button once to lock in the code.
DTS
3
VIRTUAL
6
7.1CH IN CHECKING THE CODE
9
1.
POWER
F.DIRECT
3.
PURE DIRECT
TV VCR1 DSS/VCR2 DVD
PTY
NIGHT
4.
1.
TUNER CD TAPE CDR/MD
DISPLAY
CLEAR
AUX1 AMP
2.
TV MAIN
VOL. SLEEP MUTE VOL.
BASS
OSD MENU
1.
Press and hold down the Function Selector
button for appliance which should be
controlled and press SETUP button until the
indicator blinking twice.
2.
Press the code 9 - 9 - 0.
The indicator will blink twice.
3.
To view the code for first digit, press 1 once.
Wait 3 seconds, count the indicator blinks
(e.g. 3 blinks = 3) and write down the number.
Note:
• If a code digit is "0", the indicator will not blink.
4.
Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the
third digit, and 4 for the fourth digit.
RESETTING THE ALL CODE
ENTER POWER
SET UP/
MENU OFF
T.TONE
TV VCR1 DSS/VCR2 DVD
AUTO DTS
1 2 3
1.
TUNER CD TAPE CDR/MD
NIGHT CSII EX/ES VIRTUAL
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
AUX1 AMP
7 8 9
CLEAR MEMO A/D P.SCAN/V-OFF TV MAIN
0 VOL. SLEEP MUTE VOL.
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH
OSD MENU
1.
Press and hold down the any Function
Selector button and press SETUP button until
the indicator blinking twice.
2.
Press the code 9 - 8 - 1.
The indicator will blink twice.
Then, RC5500SR will return to the factory
preset code.
Note:
• After this procedure, the selected function button
is set initial code and other function buttons are
set initial code too.
Once you have found and the codes for your various
appliances, you may want to write them down here.
TV
ENTER
VCR
SET UP/ MENU OFF
T.TONE
AUTO DTS
DSS
1 2 3
CSII EX/ES VIRTUAL
4 5 6
MCH-ST STEREO 7.1CH IN
7 8 9
DVD
MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
CD
TREBLE TUNE/SEARCH
T-MODE RDS F.DIRECT
TAPE
CDR
MD
OSD MENU
ENTER
SET UP/
MENU OFF
T.TONE
1.
PURE DIRECT AUTO DTS
1 2 3
NIGHT CSII EX/ES VIRTUAL
4 5 6
DISPLAY MCH-ST STEREO 7.1CH IN
7 8 9
2.
CLEAR MEMO A/D P.SCAN/V-OFF
0
CHANNEL/SKIP
BASS TREBLE TUNE/SEARCH