MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0631 79" X 28" EXTRA LONG DOWNDRAFT TABLE Product Dimensions: Weight................................442 lbs. Length/Width/Height......................27-3/4 x 78-3/4 x 39-3/4 in. Foot Print (Length/Width)........................27-3/4 x 78-3/4 in Shipping Dimensions: Type............................
Page 6
Main Specifications: Operation Info Air Suction Cap......................2874 CFM (1437 CFM X 2) 2874 1437 First Stage Filter Micron............................ 1 Second Stage Filter Micron..........................0.3 Filter Efficiency..................First Stage: 70%, Second Stage: 85% Impeller Type..........................Squirrel Cage Impeller Size..........................9-3/4 x 6-1/4 in. Inlet Hole Diameter............................8 in.
identification Figure 1. identification, model g0631. A. left panel B. Center panels c. downdraft plates D. right panel E. on/oFF switch dust drawer G. outlet plates model g0631 (mfg. since 3/10)
Safety instructions for Machinery SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages.
Page 9
Safety Instructions for Machinery 7. ONLY ALLOW TRAINED AND PROP- 16. REMOVE CHUCK KEYS OR ADJUSTING ERLY SUPERVISED PERSONNEL TO TOOLS. OPERATE MACHINERY. 17. DAMAGED MACHINERY. 8. KEEP CHILDREN/VISITORS AWAY. 18. DO NOT FORCE MACHINERY. 9. UNATTENDED OPERATION. 19. SECURE WORKPIECE. 10.
Page 10
Additional Safety for Downdraft Tables 1. FiLTER cApABiLiTiES. this downdraft 5. EMpTyiNG DuST DRAWER. When empty- table is to be used for wood dust collec- ing dust from the dust drawers, wear a respi- tion only. do not use this machine to filter rator and safety glasses.
SEcTiON 2: ciRcuiT REQuiREMENTS 110v Operation power connection Device this machine comes with a plug, similar to Figure 2, to connect the machine to power. this plug can be used to connect the machine to one 30 Amp circuit or two 15 Amp circuits. Serious personal injury could occur if you connect the machine to power before com- GROUNDED...
SEcTiON 3: SETup Needed for Setup This machine presents serious injury hazards the following are needed to complete the setup to untrained users. Read process, but are not included with your machine. through this entire manu- al to become familiar with Description the controls and opera- •...
inventory if any nonproprietary parts are missing (e.g. a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store. the following is a description of the main compo- nents shipped with your machine.
Site considerations Weight Load Physical Environment Machine Data Sheet Space Allocation Electrical Installation See below for required space allocation. Lighting Children or untrained people may be seriously injured by this machine. Only install in an access restricted location. Figure 4. minimum working clearances. -13- model g0631 (mfg.
Moving & placing With an assistant's help, return the downdraft table to the upright position so it rests on the Base unit footpads. Check to make sure all six footpads touch the floor evenly. Adjust individual footpads if nec- essary and secure the hex nuts against the bottom of the cabinet with a 14mm wrench.
Page 17
Align the center panel with the rear downdraft With the side panels in the upright position, table hinges, and secure with four pins, as slide the center panel brackets over the side shown in Figure 8. panels and secure with the latches, as shown in Figure 10.
Test Run turn the right motor OFF. repeat Steps 4–5 to turn the left motor ON and OFF. once the assembly is complete, test run your machine to make sure it runs properly and is remove the safety keys (Figure 12). ready for regular operation.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. Figure 14. typical sanding operation set up.
Grit 10 pack for h3120 h5918—180 Grit 10 pack for h3120 h5919—240 Grit 10 pack for h3120 Figure 16. model h3120. NOTICE Refer to the newest copy of the Grizzly catalog for other accessories available for this machine. -18- model g0631 (mfg. since 3/10)
SEcTiON 6: MAiNTENANcE Filters Always disconnect power to the machine before the filters may need to be serviced or replaced if performing maintenance. suction is noticeably reduced. the amount of use Failure to do this may has a direct bearing on how often you must ser- result in serious person- vice or change the 1"...
SEcTiON 7: SERvicE review the troubleshooting and procedures in this section to fix or adjust your machine if a problem devel- ops. if you need replacement parts or you are unsure of your repair skills, then feel free to call our technical support at (570) 546-9663.
WIRE/COMPONENT DAMAGE. MOTOR WIRING. MODIFICATIONS. CAPACITORS/INVERTERS. WIRE CONNECTIONS. CIRCUIT REQUIREMENTS. EXPERIENCING DIFFICULTIES. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -21- model g0631 (mfg. since 3/10)
Electrical components Figure 19. right switch wiring. Figure 21. Wiring for both motors. Figure 20. left motor wiring. Figure 22. right motor wiring. READ ELECTRICAL SAFETY -22- model g0631 (mfg. since 3/10) ON PAGE 21!
Wiring Diagram RIGHT PADDLE SWITCH LEFT PADDLE SWITCH (see Figure 20, page 22) The motor wiring shown here is current at the time of printing, but it match your machine. Always use the wiring diagram inside the motor junction box. MOTOR MOTOR (see Figure 20 &...
parts List PART # DESCRIPTION PART # DESCRIPTION P0631001 MAIN BASE P0631022 SMALL DUST COLLECTING PLATE P0631002 RIGHT PANEL P0631023 BIG DUST COLLECTING PLATE P0631003V2 CENTER PANEL 1PC V2.03.10 24V2 P06321024V2 MOTOR 1 HP 110V 1-PH V2.03.10 P0631005 LEFT PANEL 24V2-1 P0631024V2-1 R CAPACITOR 70M 250V V2.03.10 P0631006...
MuST maintain the original location and readability of the labels on the machine. if any label is removed or becomes unreadable, REpLAcE that label before using the machine again. contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -26-...
Page 29
WARRANTY CARD The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course, all information is strictly confidential. Note: We never use names more than 3 times. _____________________________________________________________________ _________________________________________________________________________________ _________________________________________________________________________________...
Page 32
Buy Direct and Save with Grizzly – Trusted, Proven and a Great Value! ® ~Since 1983~ Visit Our Website Today For Current Specials! ORDER 24 HOURS A DAY! 1-800-523-4777...