Ac Transient Voltage Surge Suppression And Extreme Voltage Shutdown; Extreme Voltage Shutdown Indicator; Protection Ok Indicator; Telco – Satellite – Cable Transient Voltage Surge Suppressors - Furman ELITE-15 PF i Owner's Manual

E -15 PF O ' M
i
litE wnEr s anual
®
with its power engaged permanently at a cost of pennies per month. This is an added benefit, as many audio/videophiles find
performance improves significantly when leaving low-powered components permanently charged (turned on). In fact, this is
true of the Elite-15 PF i. Though it will function flawlessly right from its shipping carton, the performance of its circuit parts will
improve after approximately two weeks of continuous use or "break-in."

AC Transient Voltage Surge Suppression and Extreme Voltage Shutdown

Extreme Voltage Shutdown Indicator:

This LED is normally off. It monitors AC wiring faults – for example, accidental connection to an open neutral from a 208 or
240VAC feed (this is a common occurrence if the 15 Amp outlet source is not a dedicated line, but instead has been wired with
a daisy-chained neutral from a homes breaker box). The Series Multi-stage Protection (SMP) circuit senses voltages that are so
high that operation would be impossible and shuts the power down before damage can occur. Upon initially applying power
to these units, the Extreme Voltage indicator LED will light if the input voltage is above the extreme voltage cutoff, and power
will not be applied to the unit's outlets. If the unit has been operating with an acceptable input voltage and subsequently that
voltage exceeds 140V or falls below 85V, it will shut off power to the outlet and the Extreme Voltage LED will light. The circuit
will attempt to re-set automatically within 5 seconds, so manual re-set will only be necessary if there is a permanent wiring fault.

Protection OK Indicator:

Although the Furman SMP circuit assures virtually maintenance free protection from transient voltage spikes and surges, nature
has a way of occasionally creating electrical forces that are beyond the capabilities of any Transient Voltage Surge Suppression
device to absorb without some degree of damage. In the rare instance that this occurs, the blue LED located in the center of
the front panel will dim, even though AC power is present at the unit's outputs. If this happens, some level of protection from
voltage surges will remain, but the Furman's clamping voltage rating will be compromised. The unit must be returned to Furman
Sound, or an authorized Furman Service center for repair.
NoTE: If the mains power is above the high cutoff voltage and has caused the unit to remove power from its outlets, it cannot
restore power without the operator manually turning the unit off, then on again. Avoid turning the unit back on, without first
checking the source of the problem, and perhaps changing the AC source.
Telco – Satellite – Cable Transient Voltage Surge Suppressors
The Elite-15 PF i features transient voltage surge suppression for both standard telephone lines, as well as cable or satellite lines
utilizing standard coaxial connectors. As these surge suppressors are in-line, they will require an additional cable to connect
from their output to the control device requiring protection.
All in-line surge suppressors feature our exclusive ground contamination free technology. This aids in eliminating audio buzzing,
and the video hum-bars that can result from typical in-line suppressors. Further, our cable and satellite suppressors are DVR
friendly as well as HD digital television ready. Both DC carrier signals as well as high bandwidth signals can pass through our
circuit. In fact the bandwidth is less than 0.1dB loss at 1GHz!
To connect your cabling to these in-line protectors, simply follow the in and out indications marked next to the Telco, Cable and
Satellite connectors.
Note: It is not possible to make an in-line cable or satellite protector "maintenance-free" as we have accomplished with the 120
VAC line. This would necessitate limited signal bandwidth that would not allow the signal to pass. Under extreme conditions, it is
possible that the surge suppression in one of these devices could sacrifice itself after a catastrophic event. If the telephone, cable
or satellite signal will no longer pass through our protector, please contact your local service representative, installer or Furman for
servicing. Since these circuits are modular, replacement may be accomplished in seconds with a new TVSS module. To test this, simply
disconnect the incoming and out going cable from the Elite-15 PF i. Connect the incoming connector to the component that formerly
received the out going connector, thus by-passing the in-line protection. If the signal is present (but not when used with the Elite-15 PF
i) then the protection circuit is damaged (assuming it worked properly before a storm or catastrophic event).