Download
Share
Print this page
Furman ELITE-15 PF i Owner's Manual
  1. Manuals
  2. Brands
  3. Furman Manuals
  4. AC Power Distribution
  5. ELITE-15 DM i
  6. Owner's manual

Furman ELITE-15 PF i Owner's Manual

Linear filtering ac power conditioner
Hide thumbs Also See for ELITE-15 PF i:

Advertisement

Quick Links

Download this manual See also: Owner's Manual
E
-15 PF
i
LITE
L
I NE AR F ILT E R I N G AC P OWE R CO ND I T I O NER
O
'
M
W N E R
S
A N UA L

Advertisement

loading

Related Manuals for Furman ELITE-15 PF i

Summary of Contents for Furman ELITE-15 PF i

  • Page 1 -15 PF LITE I NE AR F ILT E R I N G AC P OWE R CO ND I T I O NER ’ W N E R A N UA L...
  • Page 3 ENGLISH Page 4 -15 PF l’u litE uidE tilisatEur disPOniblE à www FurMansOund FRANÇAIS www.FurmanSound.com -15 PF litE anual rOPiEtariO disPOniblE En www FurMansOund ESPAÑOL www.FurmanSound.com All content ©2006 Furman Sound, LLC. All Rights Reserved. Printed in China.
  • Page 4 At the center of the Elite-15 PF i is our unique transient Power Factor Technology circuit. For the first time, low-level analog, digital, and video components are not modulated or distorted via the power amplifier’s extreme AC current demands. Further, the power amplifier sees a highly filtered, extremely low-impedance supply of AC power.

  • Page 5: Installation

    Power Source The power source to which the Elite-15 PF i is connected should be adequate for use at 15 Amps. The Elite-15 PF i will operate with a10 Amp service outlet. However, nuisance tripping at the circuit breaker panel may result if the systems continuous current draw exceeds 10 Amps.
  • Page 6 AC Cable Routing Once the Elite-15 PF i is placed, its AC cord’s female end must be plugged into the male IEC connector located on the lower left hand side of the rear panel (when facing the rear panel). Next the male Edison plug must be connected to an appropriate socket (see current rating recommendation above).
  • Page 7 When power is first applied to the Elite-15 PF i, (the front panel breaker- power toggle must be switched to the “on” position) the Soft Start feature is activated. There is an audible “clack” when the Elite-15 PF i is first turned on or off. This sound is produced by the Soft Start circuit’s 30 Amp relay engaging or disengaging.
  • Page 8 (turned on). In fact, this is true of the Elite-15 PF i. Though it will function flawlessly right from its shipping carton, the performance of its circuit parts will improve after approximately two weeks of continuous use or “break-in.”...

  • Page 9: Warranty

    If the product does not conform to this Limited Warranty during the warranty period (as herein above specified), purchaser shall notify Furman in writing of the claimed defects. If the defects are of such type and nature as to be covered by this warranty, Furman shall authorize the purchaser to return the product to the Furman factory or to an authorized Furman repair location.
  • Page 10 THIS WARRANTY IS EXCLUSIVE. The sole and exclusive obligation of Furman shall be to repair or replace the defective product in the manner and for the period provided above. Furman shall not have any other obligation with respect to this product or any part thereof, whether based on contract, tort, strict liability, or otherwise.

  • Page 11: Specifications

    Specifications AC Current Capacity: Input - 15 Amp capacity required Output - 11-15 Amps RMS (maximum, all outlets combined - continuous) Linear Noise Attenuation: Transverse (Differential) Mode: >40 dB from 10Khz. - 100 kHz. >80 dB from 100 Khz. – 1GHz. (Linear attenuation curve from 0.05 –...
  • Page 12 -15 PF ’ litE wnEr anual Notes...
  • Page 14 -15 PF ’ litE wnEr anual Notes...
  • Page 16 1690 Corporate Circle • Petaluma, California, USA 94954 Phone: 877-486-4738 • Fax: 707-763-1310 www.FurmanSound.com E15PFi_Rev2A...