Troubleshooting - Poulan Pro PP446ET Instruction Manual

Genuine Poulan or Poulan PRO bar and
chain oil is recommended to protect your unit
against excessive wear from heat and fric-
tion. Poulan or Poulan PRO oil resists high
temperature thinning. If Poulan or Poulan
PRO bar and chain oil is not available, use a
good grade SAE 30 oil,
• Never use waste eil for bar and chain
lubrication,
• Always stop the engine before removing
the oil cap,
IMPORTANT
Experience indicates that alcohol blended
fuels (called gasohol or using ethanol or
methanol) can attract moisture which teads to
separation and formation of acids during stor-
age, Acidic gas can damage the fuel system
of an engine while in storage. To avoid engine
problems, empty the fuel system before stor-
age for 30 days or longer, Drain the gas tank,
start the engine and let it run until the fuet lines
and carburetor are empty, Use fresh fuel next
season. Never use engine or carburetor
cleaner products in the fuel tank or permanent
damage may occur, See the STORAG E sec-
tion for additional information,
HOW TO STOP YOUR UNIT
• To stop the engine, move the ON/OFF
switch to the OFF position.
ON/OFF Switch
HOW TO START YOUR UNIT
WARNING:
Make sure the chain will
not make contact with any object while starting
the engine. Never try to start the unit when the
guide bar is in a cut. Avoid any contact with the
muffler. A hot muffler can cause serious bums.
_5/ _L Starting Position
HELPFUL TIP I
If your engine still does not
Pstart after fo!lowing these I
instructions, please carl
1-800-554-5728.
STARTING A COLD ENGINE
NOTE: DO NOT squeeze the throttle trigger
until the engine has started and runs.
1. Set unit on a flat surface.
2. Move ON/OFF switch to the ON position.
3. Slowly press the primer bulb 6 times.
4. Move the start lever to the START posi-
tion.
Primer
Start
Muffler
5. Pull starter rope handle sharpiy until en-
gine starts and runs.
6. Allow unit to run for 5 seconds, then fully
squeeze the throttte trigger to disengage
the starting system,
STARTING A WARM ENGINE
1. Move ON/OFF switct_ to the ON position,
2. Squeeze and hold the throttle trigger,
Keep throttle trigger fully squeezed until
engine runs smoothly,
3. Pulistarter rope sharply while squeezing
throttle trigger untit engine runs.
NOTE: Normalty, the warm starting proce-
dure can be used within 5-10 minutes after
the unit is turned OPR If the unit sits for more
than 10 minutes without being ran, it will be
necessary to start the unit by following the
steps under STARTING A COLD ENGINE or
following the starting instruction steps shown
on the unit,
STARTING A FLOODED ENGINE
Flooded engines can be started by p_acing
the ON/OFF switch in the ON position, Move
the start lever to the RUN position and fully
squeeze throttle trigger, Pull the starter han-
dle repeatedly while squeezing throttle trigger
until engine starts and runs, This could re-
quire puffing the starter handle many times,
depending on how badly the unit is flooded.
if the unit still doesn't start, refer to
TROUBLESHOOTING TABLE or call
1-800-554-6723,
OPERATING THE COUPLER
This model is equipped with a coupler which
enaMes optional attachments to be installed,
The optionat attachments are:
MODEL:
Edger ....................... PP1000E
Cultivator .................... PP2000T
Blower ...................... PP3000B
Brushcutter .................. PP4000C
'_ WARNING: Always stop unit and dis-
connect spark plug before removing or instal-
ling attachments.
REMOVING PRUNER ATTACH-
MENT, LINE TRIMMER ATTACH-
MENT, OR OTHER OPTIONAL AT-
TACHMENTS
CAUTION: When removing or installing at-
tachments, place the unit on a flat surface for
stability.
1. Loosen the coupler by turning the knob
counterclockwise.
11