Yamaha MGP32X Owner's Manual page 45

 FX2 SPX (14: SYMPHONIC)
Parameter
Frequency 0.00 – 39.7 Hz
Depth 0 – 127
Delay 0.0 – 50.0 ms
 FX2 SPX (15: DOUBLER)
Parameter
Depth 0 – 32
Range 0 – 12
Type Sound4 – Sound1, Normal, Rythm1 – Rythm4
 FX2 SPX (16: RADIO VOICE)
Parameter
Cutoff 0 – 127
Drive 0 – 127
LPF 1.0 kHz – 18.0 kHz, Thru
COMP/DUCKER/LEVELER Parameter List
 COMPRESSOR
If a signal higher than a specified threshold level is input, the output level is adjusted by a specified ratio.
Type=Comp
Parameter Range
Threshold -48 to -6 dB
Ratio 1.0 – 20.0
Attack 1 – 40 ms
Release 10 – 680 ms
Out Level -12 to +12 dB
Type=MulitiBand
Parameter Range
L-M Xover 21.2 Hz – 4.0 kHz
M-H Xover 42.5 Hz – 8.0 kHz
Release 10 – 3000 ms
Out Level -12 to +12 dB
L(/M/H)-Thresh -54 to -6 dB
L(/M/H)-Ratio 1.0 – 20.0
L(/M/H)-Attack 1 – 200 ms
L(/M/H)-Gain -INF, -36 to +18 dB
L(/M/H)-Bypass ON, OFF
 DUCKER
If the selected input source signal level exceeds the specified threshold level, the output level is attenuated by a specified amount (range).
Parameter Range
Source CH24 {CH16}, GROUP1
Threshold -60 to 0 dB
Range -70 to 0 dB
Release 1 ms – 50 s
 LEVELER
If a signal higher than a specified threshold level is input, the output level is adjusted to the specified level.
Parameter Range
Threshold -60 to 0 dB
Out Gain -20 to +40 dB
Range
Modulation frequency
Modulation depth
Delay offset
Range
Pitch shift depth
Pitch range
Effect type
Range
Filter cutoff
Distortion drive level
LPF frequency
This determines the level of input signal required to trigger the compressor.
This determines the amount of compression. A larger value results in a stronger compression
effect.
This determines how soon the signal will be compressed once the compressor has been trig-
gered.
This determines how soon the compressor returns to its normal gain once the trigger signal
level drops below the threshold.
This sets the compressor's output signal level.
Low/mid crossover frequency
Mid/high crossover frequency
This determines how soon the compressor returns to its normal gain once the trigger signal
level drops below the threshold.
Output level
This determines the level of input signal required to trigger the low/mid/high band compres-
sor.
This determines the amount of low/mid/high band compression. A larger value results in a
stronger compression effect.
Low/mid/high band compressor attack
Low/mid/high band compressor gain
Low/mid/high band bypass on/off
This determines whether the ducker source signal is channel 24 {16} or GROUP1.
This determines the level of trigger signal required to active the ducker. If the source input sig-
nal exceeds this level, the ducker begins to be applied.
This determines the amount of attenuation when the ducker is activated.
This determines how soon the ducker returns to its normal gain once the trigger signal level
drops below the threshold.
This determines the level of input signal required to trigger the leveler.
This sets leveler's output signal level.
Description
Description
Description
Description
Description
Description
Description
MGP32X/MGP24X
Appendix
45
Owner's Manual