Locking The Controls; Fault Codes; Cook & Hold - Magic Chef CER1115AAT User Manual

Locking the Controls
The touchpad controls can be locked for safety, cleaning, or
to prevent unwanted use. They will not function when locked.
If the oven is currently in use, the controls cannot be locked.
The current time of day will remain in the display when the
controls are locked.
To lock:
Press and hold the CANCEL and COOK &
HOLD pads for three seconds.
LOCK flashes in the display.
To unlock:
Press and hold the CANCEL and COOK & HOLD
pads for three seconds.
LOCK disappears from the display.
.....¸¸¸..¸¸¸"¸¸¸¸¸¸."¸¸"¸¸¸%¸¸
%¸¸¸¸¸¸¸¸:¸¸¸;¸¸¸;¸¸;¸;¸¸¸¸¸¸;¸¸::¸¸¸¸¸¸¸¸¸¸/¸¸
COOK&
HOLD
Fault Codes
BAKE or LOCK may flash rapidly in the display to alert you if
there is an error or a problem. If BAKE or LOCK flash in the
display, press CANCEL pad. If BAKE or LOCK continue to
flash, disconnect power to the appliance. Wait a few minutes,
and then reconnect power. If the flashing still continues,
disconnect power to the appliance and call an authorized
servicer.
Baking
To set Bake:
1. Press the BAKE pad. BAKE
• "BAKE" will flash.
• 000 will light in the display.
2. Select the oven temperature. The oven
temperature can be set from 170° to 550°. Press
or press and hold the A or V pads.
° 350° will light when either pad is first pressed.
• Press the A pad to increase the temperature.
• Press the V pad to decrease the temperature.
3. Press Bake pad again or wait four seconds.
° BAKE will stop flashing and light in the display.
100° or the actual oven temperature will display. The
temperature will rise in 5° increments until the preset
temperature is reached.
4. Allow the oven to preheat for 8-15 minutes.
• When the set oven temperature is reached, one long
beep will sound.
• To recall the set temperature during preheat, press the
BAKE pad.
5. Place food in center of oven, allowing a minimum of two
inches between utensil and oven walls.
6. Check cooking progress. Cook longer if needed.
7. When cooking is finished, press CANCEL.
8. Remove food from the oven.
Baking Differences Between Your Old
and New Oven
It is normal to notice some baking time differences between a
new oven and an old one. See Adjusting the Oven Temperature
on page 17.
Notes:
To change oven temperature during cooking, press
the BAKE pad, then press the A or V pad until the
desired temperature is displayed.
To change oven temperature during preheat, press
tile BAKE pad twice, then press tile A or V pad until
the desired temperature is displayed.
If you forget to turn off the oven, it will automatically turn
off at the end of 12 hours. If you wish to deactivate this
feature, see page 17.
Cook & Hold
Cook & Hold allows you to bake for a preset amount of time,
followed by a one-hour Keep Warm cycle.
To set Cook & Hold: ........................
COOK&
1. Press the COOK & HOLD pad. HOLD
• "BAKE" and "HOLD" flash.
° 000 lights in the display.
2. Select the oven temperature. The oven
temperature can be set from 170° to 550°. Press
or press and hold the A or V pad.
• Press the A pad to increase the temperature. V
° Press the V pad to decrease the temperature.
3. Press COOK & HOLD again OR wait four seconds.
• "HOLD" flashes.
• 00:00 flashes in the display.
4. Enter the amount of time you want to bake by pressing the
A or V pad. Bake time can be set from ten minutes
(00:10) to 11 hours, 59 minutes (11:59].
• "BAKE" and "HOLD" light in the display.
• The baking time will light in the display.
° The baking time will start counting down.
When the cooking time has elapsed:
° Four beeps will sound.
• "BAKE" will turn off.
• "HOLD" and "WARM" will light.
° 170°will display.
14