Advertisement
Available languages
Available languages
H
Install Ignitor
Batteries
[]
Unscrew
Ignitor
Caps
from
Control
Panel.
[]
Place
one
supplied
AA
battery
into
each
ignitor
Slot
with
positive
pole
facing
you.
[]
Position
the Cap
and
Spring
over
the
AA
battery
in each
Ignitor
Slot
and
tighten
to
Control
Panel.
Main Burners Electrode
Check
Perform
this Electrode
Check
with the
assistance
of another person.
This test will ensure
that the Spark
Electrode
Tips
are
properly
positioned
so
your
grill lights
easily
and
properly.
Spark Gap
Gas
Collector
Box
Spark Receiver
p
ctrode Tip
[]
Be
sure
all Control
Knobs
are
set
to
"OFF"
and
open
the
Grill
Lid.
[]
Have
your
assistant
stand
behind
to the
right
of the grill
and
look
toward
the front
of the grill
bowl.
Never
put your
face
inside
the
Grill
Bowl.
[]
Turn
any Control
Knob of Main Burners
to _I,
and push
in and have
assistant
watch
for a
blue
spark
within
each
Gas Collector
Box.
[]
If no spark
is seen,
the
Spark
Gap
needs
to
be
adjusted
as
follows:
•
Using
an adjustable
wrench,
loosen
the
inside
Nut until the Gas Collector
Box can
be turned
upward.
•
If the gap
between
the Spark
Elec-
trode
Tip
and
Receiver
is more
than
3/16"
use
long
nose
pliers
to gently
squeeze
the
Gas
Collector
Box
to
narrow
gap.
•
Return
the Gas Collector
Box to its
original
position,
secure
the
inside
Nut
and try the Electrode
Check
again.
If no
"clicking"
sound
is heard:
•
AA
Battery
may
be installed
back-
wards.
•
Electric
wires
may be loose.
Remove
the AA
Battery and inspect the ignitor
Junction
Box found
behind
the Control
Panel
and reconnect
any loose
wires.
H
nfrared
Burner
and
Rotisserie
Burner
Electrode
Check
[]
Open
side
burner
lid.
Remove
plastic
shipping
band
from
burner
and
pot
support.
[]
Turn
side
burner
Control
Knob
to _' and
push
in. Look
for
spark
between
tip
of
electrode
and
burner.
[]
Open
Grill
Lid.
Turn
rotisserie
burner
Control
Knob
to _I, and
push
in. Look
for
spark
between
tip
of
electrode
and
burner.
[]
If you don't see a spark from side or rotisserie
burner
electrode,
adjust
gap between
electrode
and burner
surface
to 3/16
in.
AA Batte£
11
Ignitor Cap
Ignitor Slot
_
Install
Cooking
Components
[]
Place
the
Heat
Diffusers
on
lower
ledge
above
Burners.
[]
Place
Cooking
Grids
on
bowl
ledge.
[]
Place
the
Secondary
Cooking
Rack
into
the
slots
on
Grill
Bowl
Side
Panels.
[]
Place
the
Infrared
Burner
Cooking
Grid
on
Infrared
Burner
Body.
Secondary Cooking Rack
Cooking
Heat Diffusers
Slots for Secondary
Cooking Rack
Infrared Burner
Cooking Grid
When you have finished
assembling
your
grill be sure that all screws
are tightened
for safe operation
of your grill.
Failure to read and follow the Use and Care
Instructions could result in a fire or explosion
that could cause serious bodily injury, death or
property damage.
Advertisement
