Dishwasher Feedback Section; Controls And Cycle Status; Canceling A Cycle; Changing A Cycle After Dishwasher Is Started - KitchenAid KUDC10IXBL5 User Instructions

CONTROL PURPOSE COMMENTS
To start or iesume a If the door is opened during a cycle orthe power is interrupted, the StartJResUme indicator
wash cycle flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.
"°:_!t°t'!_°'? NOTE: If the Start!Resume button is located on top of door, push door f rm!y closed within
3 seconds of pressing START/RESUME. !f the door is not closed within 3 seconds, the
StartJResume butt0n LED wi!l flash, an audible tone wi! I be heard, and the cYCle wi!l not
start.
To reset any cycle or
options during
selection.
To cancel a wash
cycle after it's
started.
Press and hold CANCEL/DRAIN to reset any control selections made.
See "Canceling A Cycle After Dishwasher Is Started" and "Changing A Cycle After
Dishwasher Is Started" sections.
To turn the audible Press and hold the Hi-Temp scrub button for3 Seconds t0 turn the audible tones on or off.
tones on croft. Only audible tones for confirming button presses can be turned 0n/off. Important audible
_or!',Q!/°":,:! tones, such as indicating a cycle has been interrupted, cannot be deactivated.
£ ee(i;tI,}acl_+{be(it_ () s
CONTROL PURPOSE COMMENTS
w:ii:i i i:_ c:il iil i:i The Cycle Status Indicator Clean indicator glows When a cycle is finished.
• • • • Lghtsareusedtofo owthe . i . . i . . .
°, ,.. / If y0u select the Sani Rinse optlon, when the Sanl R_nsecycle!sflnlshed,
progress of IRe alsnwasner
, , _ , :, _. : the Sanitized indicator g!ows, lf y0ur dishwasher did not proper!y sanitize
cycle Locatecl on me Tront
of the d s[qwasher for front your dishes, the light flashes at the end of the cYClel This can happen if the
. , ,, ,; . ; cycle is interrupted or the water could not be heated to the required
contro moaes ann ocatea tem er t r ....
...................................... on the top of the do0r for P
hidden control models. The Clean and Sanitized lights go off when you open and close the door or
)ress and hold CANCEL.
A
The Front Indicator Light or
Single Exterior Light (A)
shows progress of your
dishwasher cycle by color.
(Available on some hidden
control models only).
The light will be blue if the dishwasher is washing or rinsing. The light will
be red when the dishwasher is drying. The light will be green to indicate
that the cycle is complete. If the Front Indicator Light is blinking, see
"Troubleshooting" section.
The Cycle Status Display is The indicators Wi!l inform you if you are able to add a dish to the Cycle after
• : _ ..... used to follow the progress it has started. It wi!! a!so inform you if the dishwasher is washing rinsing
;.. : u ..... '" ' of the dishwasher cycle, and drying, complete, and/or sanitized. They will show whether the control is
to show other nformation, locked and!or the delay option is selected. A series of bars will count down
(Availab!e on some models the duration of the cycle remaining from left to right, Each bar equa!s
instead of Cycle Status approximately 24 minutes of cycle lengthi The bars will also count down
Indicator Lights)the delay feature from left to right, and the de!ay indicator will be activated.
Canceling A Cycle
1. Press and hold the Cancel/Drain button once. The Cancel/
Drain light will turn on. If the Cancel/Drain button is located on
the top of the door, open the door slightly to stop the cycle.
Wait for the spraying action to stop before completely opening
the door. Press and hold the Cancel/Drain button once.
2. Close the door and the dishwasher starts a drain cycle (if water
remains in bottom of dishwasher). Let the dishwasher drain
completely. The Cancel/Drain light turns off after 2 minutes.
Changing A Cycle After Dishwasher Is Started
1. You can interrupt a cycle and restart your dishwasher from the
beginning using the following procedure.
2. Press and hold the Cancel/Drain button twice to reset the
control. If the Cancel/Drain button is located on the top of the
door, open the door slightly to stop the cycle. Wait for the
spraying action to stop before completely opening the door.
Press and hold the Cancel/Drain button twice to reset the
control.
10
3. Select new cycles and options.
4. Press START/RESUME.
Adding A Dish After Dishwasher Is Started
1. Check if Add a Dish indicator is lit. (Available on some models.
Otherwise, proceed to Step 2.)
2. Open the door slightly to stop the cycle. Wait for the spraying
action to stop, then open the door completely.
3. Check whether the detergent dispenser cover is still closed. If
it is open, the wash cycle has already started and adding a
dish is not recommended.
4. If detergent has not yet been used (detergent dispenser cover
is closed), you may add a dish.
5. Press START/RESUME.