Dishwasher Feedback Section - KitchenAid KUDE48FXSP Use & Care Manual

Use & care guide
Hide thumbs Also See for KUDE48FXSP:
Table of Contents

Advertisement

Available languages

Available languages

OPTION SELECTIONS
OPTIONS
Control Lock
Avoids unintended use of the dishwasher between cycles, or cycle and option changes during a cycle.
To turn on Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The Control
Lock light will stay on for a short time, indicating that it is activated, and all buttons are disabled. If you press any button
while your dishwasher is locked, the light flashes 3 times. The dishwasher door can still be opened/closed while the
or
controls are locked.
NOTE: You may need to disable Sleep Mode by pressing either START/RESUME or CANCEL, or by opening and
closing the door before you are able to turn Control Lock off.
To turn off Control Lock, press and hold CONTROL LOCK or 4 HOUR DELAY (depending on model) for 3 seconds. The
light turns off.
NOTE: If your model requires you to press and hold 4 HOUR DELAY to lock the controls, the Control Lock LED will be
on or off to indicate if Control Lock is active or not.
CONTROLS AND CYCLE STATUS
CONTROL
PURPOSE
To start or resume a
wash cycle
To reset any cycle or
options during
selection.
To cancel a wash
cycle after it's
started.
To turn the audible
tones on or off.
CONTROLS AND CYCLE STATUS
CONTROL
A
10
CAN BE
SELECTED WITH
COMMENTS
If the door is opened during a cycle or the power is interrupted, the Start/Resume indicator
flashes. The cycle will not resume until the door is closed and START/RESUME is pressed.
NOTE: If the Start/Resume button is located on top of door, push door firmly closed within
3 seconds of pressing START/RESUME. If the door is not closed within 3 seconds, the
Start/Resume button LED will flash, an audible tone will be heard, and the cycle will not
start.
Press and hold CANCEL/DRAIN to reset any control selections made.
See "Canceling A Cycle After Dishwasher Is Started" and "Changing A Cycle After
Dishwasher Is Started" sections.
Press and hold the Hi-Temp Scrub button for 3 seconds to turn the audible tones on or off.
Only audible tones for confirming button presses can be turned on/off. Important audible
tones, such as indicating a cycle has been interrupted, cannot be deactivated.

Dishwasher Feedback Section

PURPOSE
The Cycle Status Indicator
Lights are used to follow the
progress of the dishwasher
cycle. Located on the front
of the dishwasher for front
control models, and located
on the top of the door for
hidden control models.
The Front Indicator Light or
Single Exterior Light (A)
shows progress of your
dishwasher cycle by color
(for hidden control models
only).
The Cycle Status Display is
used to follow the progress
of the dishwasher cycle, and
to show other information.
(Available on some models
instead of Cycle Status
Indicator Lights)
WHAT IT DOES
COMMENTS
Clean indicator glows when a cycle is finished.
If you select the Sani Rinse option, when the Sani Rinse cycle is finished,
the Sanitized indicator glows. If your dishwasher did not properly sanitize
your dishes, the light flashes at the end of the cycle. This can happen if the
cycle is interrupted, or the water could not be heated to the required
temperature.
The Clean and Sanitized lights go off when you open and close the door or
press and hold CANCEL.
The light will be blue if the dishwasher is washing or rinsing. The light will
be red when the dishwasher is drying. The light will be green to indicate
that the cycle is complete. If the Front Indicator Light is blinking, see
"Troubleshooting" section.
The indicators will inform you if you are able to add a dish to the cycle after
it has started. It will also inform you if the dishwasher is washing, rinsing,
drying, complete, and/or sanitized. They will show whether the control is
locked and/or the delay option is selected. A series of bars will count down
the duration of the cycle remaining from left to right. Each bar equals
approximately 24 minutes of cycle length. The bars will also count down
the delay feature from left to right, and the delay indicator will be activated.
ADDED TIME TO CYCLE
TYPICAL
MAX
ADDED
WATER
GALLONS
(LITERS)

Advertisement

Table of Contents
loading

Table of Contents