Kenmore 122.16654901 Use And Care Manual page 14

Toensure a proper w orking unitthefollowing proper
careandmaintenance is suggested.
CleaningCookingGrids
Wesuggest youwashyourcooking gridsina mildsoap
andwarmwatersolution. Youcanusea washclothor
softbrush tocleanyourcooking grids.
CleaningHeatdiffusers
Periodically youshould washtheheatdiffusers ina
soapandwarmwatersolution. Usea softbrushto
remove stubborn burnt-on c ooking residue. Theheat
diffusers s houldbedrybefore youreinstall them.
CleaningGrease Tray
Thegrease trayshould beemptied andwiped
downperiodically andwashed ina mild
detergent andwarmwatersolution. Asmall
amount o fsandor catlittermaybeplaced in
bottom ofgrease traytoabsorb thegrease.
Check thegrease trayfrequently, don'tallow
excess grease toaccumulate a ndoverflow outofthe
grease tray.
Annual Cleaning of Grill Interior
Burning-off the grill after every use will keep it ready for
your next use. However, once a year you should give
the entire grill a thorough cleaning to keep it in top
operating condition. Follow these steps.
1. Turn all burner valves to full OFF position.
2. Turn LP gas tank valve to full OFF position.
3. Detach LP gas hose and regulator assembly from
your gas grill. Inspect for any damage and replace as
necessary with manufacturer replacement part number
found on parts list.
4. Remove and clean heat diffusers, cooking grids and
grill burners.
5. Cover each gas valve orifice with aluminum foil.
6. Brush inside and bottom of grill with a nylon brush,
and wash with a mild soap and warm water solution.
Rinse thoroughly and let dry.
7. Remove the aluminum foil, then reinstall heat
diffusers, and cooking grids.
8. Reconnect gas source and observe burner flame for
correct operation.
Cleaning Exterior Surface
•We suggest you wash your grill using a mild soap and
warm water solution. You can use a wash cloth or
sponge for this process. Do not use abrasives or a
brush that might remove finish during the cleaning
process.
Cleaning Exterior Stainless Steel Surfaces
•Weathering and extreme heat can cause exterior
stainless steel surfaces to turn tan in color. Machine
oils used in manufacturing process of stainless steel
can also cause this tanning color. Use a stainless
steel cleaner to polish stainless steel surfaces of
your grill. Never use abrasive cleaners or scrubbers
because they will scratch and damage your grill.
Cleaning Burner Tubes and Burner Ports
To reduce the chance of "FLASH-BACK" the procedure
below should be followed at least once a month in late
summer or early fall when spiders are most active or
when your grill has not been used for a period of time.
1. Turn all burner valves and gas tank valve to off
position.
2. Detach the LP gas regulator assembly from your gas
grill.
3. Remove cooking grids, heat diffusers, and grease
tray from the grill.
4. Remove the screws from the underside of each
burner and lift the burners up and away from the gas
valve orifice.
5. Using a bent stiff wire in the shape of a hook, air
hose or a bottle brush, run it through the burner tube
and inside several times to remove any debris.
6. Replace burners, see illustration below.
Step 1. Locate the burner onto the orifice.
Step 2. Secure the main burner on the back wall of fire
box with 2 screws.
_.I WARNING
The location of the burner tube with respect to the
orifice is vital for safe operation. Check to ensure the
orifice is inside the burner tube before using the gas
grill. If the burner tube does not fit over the valve
orifice, lighting the burner may cause explosion
and/or fire.
14