Table of Contents
Advertisement
6 APPENDIX A: BASIC SETTINGS AT EKB 500 KEYBOARD
The following chapter describes the basic settings in the EKB 500 keyboard to establish communication
with speed dome cameras.
6.1 COM PORT SETTING - RS-485 INTERFACE SETTING
Telemetry protocol type and transmission rate are defined in this menu.
M
E
N
U
> COM PORT SETTING >
M
E
N
U
M
E
N
U
Select port 1 or 2 and confirm with
Use the
J
O
Y
S
T
I
C
K
J
O
Y
S
T
I
C
K
J
O
Y
S
T
I
C
K
Selection: 1200, 2400, 4800, 9600 Baud.
Press
E
N
T
E
R
to confirm the setting and
E
N
T
E
R
E
N
T
E
R
The next menu is used for telemetry protocol
setting.
Use the
J
O
Y
S
T
I
C
K
J
O
Y
S
T
I
C
K
J
O
Y
S
T
I
C
K
Selection:
EVF-2:
Pelco-D
Pelco-P
NOTE: Baud rate and protocol type have to comply with the EPTZ 100 settings for these parameters
(DS1 DIP switch setting).
Press
E
N
T
E
R
to confirm the selection and
E
N
T
E
R
E
N
T
E
R
6.2 DEVICE SETTING > CAMERA
Define in this menu RS-485 ID (address) and connected RS-485 port:
M
E
N
U
> DEVICE SETTING > CAMERA SETTING >
M
E
N
U
M
E
N
U
Camera number 1 ~ 9999 (independent from RS-485 address!)
Press Enter to confirm the setting and Esc to cancel.
Setup of the RS-485 interface which is connected to EPTZ 100,
port 1 or 2.
Press Enter to confirm the setting and
Enter the RS-485 address of the EPTZ 100.
If the camera is connected to an EverFocus DVR, enter the
DVR number and video input number.
Enter any value if no DVR is connected
(numeric entry compulsory).
Press
E
N
T
E
R
to confirm the setting and
E
N
T
E
R
E
N
T
E
R
E
N
T
E
R
E
N
T
E
R
E
N
T
E
R
E
N
T
E
R
.
E
N
T
E
R
E
N
T
E
R
to change the value.
E
S
C
to cancel.
E
S
C
E
S
C
to change the value.
recommended protocol for optimized EKB 500 functionality
E
S
C
E
S
C
E
S
C
E
S
C
to cancel.
E
S
C
E
S
C
E
S
C
to cancel.
E
S
C
E
S
C
Port : _ ( 1 or 2 )
Input the port.
BAUD : 9600 <
[ ↑ ↓ ] to change
Protocol : EVF-2
[ ↑ ↓ ] to change
to cancel.
Port : 1 Changed
[ ENT ] to save
Camera Name : ___
E
N
T
E
R
E
N
T
E
R
E
N
T
E
R
RS485 Connected to
Port : _ [ 0 (off) ] , 1, 2]
RS485 Address:
001
Video Connected to
DVR: _ _ _ CH : _ _
Camera: 0001 changed
[ENT] to save
45
EPTZ100_ma_en_rev03.doc
Advertisement
Table of Contents
