Advertisement
Available languages
Available languages
5. Squeeze thefilter to
spread a ndremove
excess o il(Fig. 1 7).
6. Replace theairfilter
inside theairfilter/muffler
cover ( Fig. 1 4).
NOTE: O perating theunit
without theairfilter
and airfilter/muffler
cover a ssembly will
VOID thewarranty.
Reinstalling the Air
Filter/Muffler
Cover
Fig. 17
Spark Arrestor Hood
Engine
1.
Place the air filter/muffler
,/
Slo_,
c°ver°vertheback°fthe
cr_ew_sp_ark
_
carburetor and muffler.
Align the screw holes.
2.
Insert the four (4) screws
into the holes in the air
S
filter/muffler
cover (Fig.
Tabs
Screen
Muffler
13) and tighten. Do not
Fig. 18
over tighten.
SPARK ARRESTOR MAINTENANCE
i
'*thes ar arrestorhoodan
I
screen are not tightened securely, they could fall off causing
damage to the unit and possible serious personal injury.
NOTE:
Pay close attention when disassembling
the muffler so you
can put it back together correctly. Failure to do so will
damage the unit and may cause serious personal injury.
1.
Remove air filter/muffler
cover. Refer to Removing the Air
Filter/Muffler
Cover.
2,
Locate the muffler, but do not remove it. Find the screw on the
bottom of the muffler (Fig. 18). This screw holds the Spark
Arrestor Hood Assembly and the spark arrestor screen to the
bottom of the muffler. Remove this screw using either a Torx
T20 or flat blade screwdriver.
3.
Using a small flat blade screwdriver, carefully pry up the spark
arrestor screen from the recessed hole, taking care to notice that
the "raised" part of the spark arrestor screen is inside the
recessed hole. Remove the spark arrestor screen from the muffler.
4.
Clean the spark arrestor screen with a wire brush. Replace it if it
is damaged, or if you are unable to clean it thoroughly.
5.
Reinstall the spark arrestor screen by putting the "raised"
portion of the screen inside the recessed hole of the muffler.
Make sure that the spark arrestor screen fits flat against the
muffler.
6.
Place the spark arrestor hood on top of the spark arrestor plate
with the "raised" side up and the opening facing AWAY from the
engine (Fig. 18). Verify that the exhaust will be directed AWAY
from the engine.
7.
Replace the screw you removed in Step 2 and tighten securely.
8.
Reinstall the air filter/muffler
cover (Fig. 13).
CARBURETOR
ADJUSTMENT
NOTE:
Careless adjustments can seriously damage your unit. Contact
a Sears or other qualified service dealer to make carburetor
adjustments. Call 1-800-4-MY-HOMEefor
more information.
REPLACING THE SPARK PLUG
iw.o...o=
oonotsand .ast,
scra eorc.eans ar .u0
I
electrodes. Grit in the engine could damage the cylinder.
Use a Champion RDJ7Y spark plug or equivalent.
Remove the plug
after every 25 hours of operation and check its condition.
1.
Stop the engine and allow it to cool. Grasp the plug boot firmly
and pull it from the spark plug.
2.
Clean around the spark plug. Remove the spark plug from the
cylinder head by turning a 5/8-inch socket counterclockwise.
3.
Replace a cracked, fouled
or dirty spark plug. Set
the air gap at 0.025 in.
(0.635 ram) using a feeler
gauge (Fig. 20).
4.
Install a correctly-gapped
spark plug in the cylinder
0.025 in.
head. Tighten by turning the (0.635 ram)
5/8-inch socket clockwise
t
until snug. If using a torque
wrench, torque to:
Fig. 20
110-120 in..Ib.
(12.3-13.5 N.m).
Do not over-tighten.
5.
Reattach the plug boot.
TRANSPORTING
• Allow the engine to cool before transporting.
• Drain fuel from unit.
• Tighten fuel cap before transporting.
• Secure the unit while transporting.
CLEANING
_,
WARNING:
To avoid serious personal injury, always turn your I
tr mmer off and a ow t to coo before you c ean or manta n t.
I
m
Use a small brush to clean off the outside of the unit. Do not use strong
detergents. Household cleaners that contain aromatic oils such as pine
and lemon, and solvents such as kerosene, can damage plastic housing
or handle. Wipe off any moisture with a soft cloth.
STO RAG E
• Never store a fueled unit where fumes may reach an open flame or spark.
• Allow the engine to cool before storing.
• Store the unit locked up to prevent unauthorized
use or damage.
• Store the unit in a dry, well-ventilated
area.
• Store the unit out of the reach of children.
LONG TERM STORAGE
If you plan on storing the unit for an extended time, use the
following storage procedure:
1.
Carefully drain the fuel tank by running the unit dry or remove
fuel cap and tip the motor housing over and drain oil/gas fuel
into a container with the same 2-cycle fuel mixture. Do not use
fuel that has been stored for more than 60 days.
2.
Start the engine and allow it to run until it stalls. This ensures
that all fuel has been drained from the carburetor.
3.
Allow the engine to cool. Remove the spark plug and put 1 oz.
(30 ml) of any high quality motor oil or 2-cycle oil into the
cylinder. Pull the starter rope slowly to distribute
the oil.
Reinstall the spark plug.
NOTE:
Remove the spark plug and drain all of the oil from the
cylinder before attempting to start the trimmer after storage.
4.
Thoroughly clean the unit and inspect it for any loose or
damaged parts. Repair or replace damaged parts and tighten
loose screws, nuts or bolts. The unit is ready for storage.
Advertisement
