WARNING!READ ANDUNDERSTAND ALL
INSTRUCTIONS. Failure to follow aHinstructions
Hsted below, m ayresuUt ineUectric shock, f ireand/or
serious personal injury.
SAVE THESE INSTRUCTIONS
m Keepyourwork areacleanandweJJ l it. CUuttered
benches a nddarkareasinviteaccidents.
m Donot operate
power tools in expJosive atmo-
such as in the presence of flammable
liquids, gases, or dust.
Power tooUscreate sparks
which may ignite the dust or fumes.
m Keep bystanders,
a power tool. Distractions can cause you to
m A battery operated tooJ with integral
separate battery pack must be recharged
charger for the battery. A charger that
may be suitable for one type of battery may create a
risk of fire when used with another battery.
m Use battery operated
toot onJy with specifically
battery pack. Use of any other batteries
may create a risk of fire.
R Use battery only with charger
Art. No. 911044
Art. No. 911401
n Do not abuse the cord. Never use the cord to carry
Keep cord away from heat, oil, sharp
edges, or moving
parts. RepJace damaged
Damaged cords may create a fire.
m Stay aJert, watch what you are doing and use
sense when operating
a power tool
not use tooJ while tired or under the influence
drugs, alcohol, or medication.
A moment of inatten-
tion while operating power tools may result in serious
m Dress properly.
Do not wear loose clothing
jewelry. Contain long hair. Keep your hair, clothing,
and gloves away from moving parts. Loose clothes,
jewelry, or long hair can be caught in moving parts=
m Avoid accidental
Be sure switch is in the
locked or off position
pack. Carrying tools with your finger on the switch or
inserting the battery pack into a tool with the switch on
m Remove adjusting
keys or wrenches
the tooJ on. A wrench or a key that is left attached to a
rotating part of the tool may result in personal injury.
m Do not overreach. Keep proper footing and batance
at aH times. Proper footing and balance enable better
control of the tool in unexpected situations.
m Use safety equipment.
AJways wear eye protection.
Dust mask, non-skid safety shoes, hard hat, or hearing
protection must be used for appropriate conditions.
m Do not wear loose clothing
hair. Loose clothes, jewelry, or long hair carl be drawn
into air vents.
m Do not use on a ladder or unstable support.
footing on a solid surface enables better control of the
tool in unexpected situations
TOOL USE AND CARE
m Use clamps
or other practical
way to secure and
to a stabte platform.
the work by hand or against your body is unstable and
may lead to loss of control.
m Do not force tool. Use the correct tooJ for your
The correct tool will do the job better and
safer at the rate for which it is designed.
m Do not use tool if switch does not turn it on or off. A
tool that cannot be controlled with the switch is danger-
ous and must be repaired.
battery pack from tooJ or place the
switch in the locked or off position
Such preventive safety measures reduce the
risk of starting the tool accidentally.
m Store idle tooJs out of reach of children
Tools are dangerous in the hands
of untrained users.
m When battery pack is not in use, keep it away from
other metal objects
Jike: paper clips, coins, keys,
naris, screws, or other small metal objects that can
make a connection
from one terminal
Shorting the battery terminals together may cause
sparks, burns, or a fire.
m Maintain tooJs with care. Keep cutting
and cJean. Properly maintained tools with sharp cutting
edges are less likely to bind and are easier to control
m Check for misa_ignment
of moving parts,
breakage of parts, and any other condition
affect the tool's operation,
ff damaged, have the too_
before using. Marly accidents are caused by
poorly maintained tools.
Use only accessories
that are recommended
for your model
Accessories that may
be suitable for one tool may create a risk of injury when
used on another tool.
Keep the tool and its handle dry, dean and free
from oi_ and grease. Always use a clean cloth when
cleaning. Never use brake fluids, gasoline, petroleum-
based products, or any strong solvents to clean your
tool. Following this rule will reduce the risk of loss of
control and deterioration of the enclosure plastic.