Page of 12

CRAFTSMAN 315.271410 Owner's Manual Page 3

Hide thumbs
RULES FOR SAFE OPERATION
(Continued)
14.
DON'T ABUSE CORD.
Never carry tool by cord
or yank it to disconnect from receptacle.
Keep
cord from heat, oil and sharp edges.
15.
SECURE
WORK.
Use clamps or a vise to hold
work. Beth hands are needed to operate the tool.
16.
DON'T OVERREACH.
Keep proper footing and
balance at all times. Do not use on a ladder or
unstable support.
17,
MAINTAIN TOOLS WITH CARE. Keep tools sharp
at all times,
and
clean
for best
and safest
performance.
Follow instructions for lubricating
and changing accessories.
18,
DISCONNECT
TOOLS,
When not in use. before
servicing, or when changing attachments, blades,
bits, cutters, etc., all tools should be disconnected
from power supply.
19,
REMOVE
ADJUSTING
KEYS
AND
WRENCHES.
Form habit of checking to see that
keys and adjusting
wrenches are removed from
tool before turning it on.
20
AVOID
ACCIDENTAL
STARTING.
Don't carry
plugged-in
tools with finger on switch. Be sure
switch is off when plugging in.
21.
MAKE
SURE YOUR
EXTENSION
CORD
IS IN
GOOD
CONDITION.
When using an extension
cord, be sure to use one heavy enough to carry the
current your product wilrdraw.
An undersized cord
will cause a drop in line voltage
resulting in loss of
power and overheating.
A wire gage size (A.W.G.)
of at least 16 is recommended
for an extension
cord 100 feet or less in length. A cord exceeding
1O0 feet is not recommended.
If in doubt, use the
next heavier
gage. The smaner the gage number,
the heavier
the cord.
22.
OUTDOOR
USE EXTENSION
CORDS.
When
tool is used Outdoors, use only extension cords
suitable for use outdoors. Outdoor approved cords
are marked
with the suffix W-A, for example -
SJTW-A or SJOW-A,
23,
KEEP BITS
CLEAN
AND SHARP.
Sharp bits
minimize
stalling and kickback.
24.
KEEP HANDS AWAY FROM
DRILLING
AREA.
Keep
hands
away
from
bits. Do not reach
underneath
work while bit is rotating.
Do not
attempt to remove material while bit is rotating.
25.
NEVER USE IN AN EXPLOSIVE
ATMOSPHERE.
Normal sparking of the motor could ignite fumes.
26,
INSPECT TOOL CORDS
PERIODICALLY
and if
damaged,
have repaired at your nearest Sears
Repair
Center.
Stay constantly
aware of cord
location
27.
INSPEC'r EX'rENSION
CORDS PERIOD4CALLY
and replace if damaged.
28,
KEEP
HANDLES
DRY,
CLEAN,
AND
FREE
PROM OIL AND GREASE.
Always use a clean
cloth when cleaning.
Never
use
brake fluids,
gasoline, p_roleum-besed
products or any st reng
solvents to clean your tool.
29.
STAY ALER3". Watch what you are doing and use
common sense. Do not operate tool when you are
tired. Do not rush.
30.
CHECK
DAMAGED
PARTS.
Before further use
of the tool, a guard or other part that is damaged
should be carefully checked to determine
that it
will operate
proberly and perform
its intended
function. Check for alignment
of moving parts,
binding
of moving
parts,
breakage
of parts,
mounting,
and any other conditions that may
affect its operation. A guard or other part that is
damaged should be proparly repaired or replaced
by an authorized service center unless indicated
elsewhere in this instruction manual,
31.
DO NOT
USE TOOL
IF SWITCH
DOES
NOT
TURN IT ON AND OFF. Have defective switches
replaced by an authorized service center.
32.
DRILLING
INTO
ELECTRICAL
WIRING
IN
WALLS
CAN CAUSE DRILL
BIT AND CHUCK
TO BECOME
ELECTRICALLY
LIVE,
Do not
touch the chuck or metal housing when dnlling
into a wall; grasp only the insulated handle(s)
provided on the tool.
33,
inspect for and remove all nails from lumber
before dhlling.
34.
DRUGS,
ALCOHOL,
MEDICATION.
Do
not
operate tool while under the influence of drugs,
alcohol, or any medication.
35.
When servicing
use only identical
Craftsman
replacement
part==.
36,
POLARIZIED PLUGS, To reduce the dsk of electric
shock, this tool has a polarized plug (one blade is
wider than the offier). This plug will fit in a peladzed
outlet only one way. If the plug does not fit fully in
the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician
to install the proper
outlet. Do not change the plug in any way.
37.
SAVE
THESE
INSTRUCTIONS.
Review
them
frequently and use them to instruct others who
may use this tool. If you loan someone this tool,
loan them these instructions also.
Page 3

   Related Manuals for CRAFTSMAN 315.271410

Comments to this Manuals

Symbols: 0
Latest comments: