Power Source - Craftsman 351.226060 Operator's Manual

• Loosen and remove hex head bolt and flat washer from the
disc table.
• Replace hex head bolt with the handle provided. Secure
disc table to disc guard using the handle and fiat washer.
ATTACH ABRASIVE DISC TO ALUMINUM DISC
Refer to Figures 3, 4 and 1t+
• Sander is shipped with the abrasive (KeyNo. 5) not applied
to the aluminum disc (Key No. 1).
• Clean the aluminum disc if necessary prior to applying the
abrasive.
• Remove the adhesive cover from the back of the abrasive
disc.
• Slide the abrasive between the disc table and aluminum
disc and center abrasive on the aluminum disc.
• Apply pressure on abrasive to paste.
• Make sure abrasive is pasted evenly on the aluminum disc.
Figure 3 - Attach Abrasive Disc
• Make sure that the clearance between disc table and abra-
sive disc does not exceed 1/_,,
Figure 4 - Check Disc Table
• Use a straight edge or square to check if the disc table is at
right angle to the disc.
• Wear a protective glove and manually turn the disc to verify
that the disc turns freely and without interference.
ATTACH MITER GAUGE
Refer to Figure 11,
Required part: Miter gauge assembly
• Miter gauge is shipped completely assembled (Key No. 9)
and can be used with the belt or disc tables (Key Nos. 63
and 24).
• Slide miter gauge bar (Key No. 76) into the slot on belt or
disc table.
R_er to Figures 5, 6, and 7, pages 4-5.
Sander comes with the motor and wiring installed. The
115/230-volt AC universal motor has the following specifica-
tions.
NOTE: Though the motor works at 115/230-volt AC, sander
must be operated at 115 volts only.
Horsepower (Maximum Developed) ................... 3
Amperes ...................................... 15
Frequency .................................. 60 HZ
Phase ..................................... Single
RPM ....................................... 3450
Prewired .................................... 115V
WARNING: All electrical connections must be performed by
a qualified electrician.
WARNING: Do not connect sander to the power source until
all assembly steps have been completed.
POWER SOURCE
The motor is designed for operation on the voltage and fre-
quency specified. Normal loads will be handled safely on volt-
ages not more than 10% above or below specified voltage.
Running the unit on voltages which are not within the range
may cause overheating and motor burn-out. Heavy loads
require that the voltage at motor terminals be no less than the
voltage specified on nameplate.
• Power supply to the motor is controlled by a single pole
locking rocker switch. Remove the key to prevent unautho-
rized use.
GROUNDING INSTRUCTIONS
WARNING: Improper connection of equipment grounding
conductor can result in the rLskof electrical shock, Equipment
should be grounded while in use to protect operator from
elect rioal shock,
• Check with a qualified electrician if grounding instructions
are not understood or if in doubt as to whether the tool is
properly grounded.
• This tool is equipped with an approved 3-conductor cord
rated at 240V and a 3-prong grounding type plug rated at
125V (Figure 5) for your protection against shock hazards.
• Grounding plug should be plugged directly into a properly
installed and grounded 3-prong grounding-type receptacle,
as shown (Figure 5).
ProP::Llyn d Gi i ;u_ rdoendg OutIet _._
3 Prong Plug
Figure 5 - 3-Prong Receptacle
• Do not remove or alter grounding prong in any manner. In
the event of a malfunction or breakdown, grounding pro-
vides a path of least resistance for electrical shock.
WARNING:
Do not permit fingers to touch the terminals of
plug when installing or removing from outlet.
• Plug must be plugged into matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances. Do not modify plug provided. If it will not fit
in outlet, have proper outlet installed by a qualified
electrician.
• Inspect tool cords periodically, and if damaged, have
repaired by an authorized service facility.
4