Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Craftsman 171.25490
Summary of Contents for Craftsman 171.25490
- Page 1 Save This Manua!_ For Future Reference owners manual MODEL 171.25490 CRRFTSMRH INDUSTRIAL ROUTER TABLE CAUTION: READ ALL INSTRUCTIONS • assemb y CAREFULLY , operatinq _.._ ..Sold bY SEARS. ROEBU(_KiAND CO., CH|CAGO,_i 6068_, U.S.A. Printed In U.S.A. 49LCN-39...
- Page 2 WARNING: FAILURE TO HEED ALL SAFETY AND OPERATING INSTRUCTIONS AND WARNINGS REGARDING UI_tEI OF THIS PRDDUCT CAN RESULT IN SERIOUS BODILY INJURY. ° GENERAL SAFETY INSTRUCTIONS FOR POWER TOOLS 1. KNOW YOUR POWER TOOL 13. SECURE WORK Read the owner's manual carelulty. Learn _IS applicalion and Use clamps or a wse ,'o hold work when practical.
- Page 3 NOTE: it is far safer and convenient to use a "Sears Should be blown out, or "vacuumed", frequently to prevent interference with Craftsman 925C60 Router Table Switch normal me;or ventilation. Package". This switch provides a key operated ON/OFF button WhiCh allows very...
- Page 4 INTRODUCTION How otlen have you needea a large guiclingsurface on a e, Dust collecting attachment for most shop vac hook muter table? Your Sears Craftsman Industrial Router ups. Table wilh Unitized Fence comes with: To increase the work surface of your muter table, "Sears a.
- Page 5 #10-32 Stop nut Top of Talkie MOUNTING ROUTER TO TABLE ALWAYS UNPLUG ROUTER BEFORE MOUNTING (The table is designed to accept most Sears Craftsman Routers. However, i1 will accommodate other brancls with bases up to 7" in diameter by properly aligning,...
- Page 6 (It will be helpful il you orient the router such Ihat you can easily reach the ONIOFF switch from the front of the table. Sears Craftsman 925090 Router ATTACHING OTHER BRANDS OF REUTERS Table Switch Package provides easy access to ON/ OFF button).
- Page 7 NOTE: It l_e head of the screw is "V-shaped" you wltl be countersinking. With lhe desired bit in the ,'outer, select a throat plate insert with a center h01e slightly larger than the diameter ff the head of the screw is net "V-shaped" you of the router bit, NOTE: For bits 1- =/_"...
- Page 8 ASSEMBLY OF UNITIZED FENCE WARNING: BEFORE ASSEMBLING AND AT'rACI_. You will observe as you face the front of the lab_e, that ING UNITIZED FENCE TO TABLEs MAKE SURE THAT ROUTER IS UNPLUGGED AND THE BIT IS BELOW on the right side of the table top there are two round holes approximately =/="...
- Page 9 Farallrouting operations IJepenamg upon Ine roulsng operalton, insert one ol a way from edge on the unaer- the "2-20 x 1_/4 '' long carnage belts through one ot side of workpiece, suctl as Gn3oving, Fluting, Veining, Crown Molding, etc., at!act1f:ence using back hole and the holes on the right side o! the of the table top (from the underside) and the short slot in the fence.
- Page 10 ONLY of 1he PUSH Unitized fence is provided with a hookup for most Sears BLOCK will greatly improve the sliding Craftsman 21Iz"hose diameter vacs. motion. Attach 21/z '' hose nozzle as shown in Figure 20. FOR ROUTING ON ENDS (TENONS, SLIDING DOVE- TAILS, ETC.) THE WORKPIECE IS HELD AGAINST...
- Page 11 B. TO SEARS LEG SET #22235 NOTE: OPERATING ROUTER TABLE WITHOUT USE OF WETJDRY VAC MAY RtS_SULT IN EXCESSIVE Assemble lag set as directed by the inslructions COLLECTION OF SAWDUST AND CHIPS UNDER THE included with the leg set. FENCE AND THE GUARD. REMOVE DUST AND CHIPS FROM UNDER Title 1.
- Page 12 ASSEMBLY OF MITER GAUGE-" The unitized fence on your table is providecl as a guide against which the workpiece should be held for accurac'y in routing. Free hand routing (not holding work_againsl Assemble prolractor head to miter bar as shown in the fence) is hazardous and should be strictly avoided Figure 23.
- Page 13 of bil is aligned with line "B". (Refer to you-t-muter's owner's manual !or adjusting your router properly). AFTER MAKING THIS ADJUSTMENT, BE SURE ROUTER IS SECURELY TIGHTENED IN THE ROUTER BASE, THE BIT IS SECURELY TIGHTENED ----'_ IN THE ROUTER CHUCK, AND ROUTER BASE IS TIGHTLY SECURED TO TABLE TOP.
- Page 14 NOTE: The push block, and clamp plate asser_bly will 4. Test cut a piece of scrap wood:to make sure adjust not accommodate workpieces wider _han 4", menls are satistaclory. EXAMPLE: CUTTING TENONS NOTE: Feed work against the rotation of 1he cutter (in the direction shown by the arrow in Figure 27), 1, Make ¢erlain thai jointing fence is locked inposition with its lace flush with that ol unitized fence.
- Page 15 in the same manner as in step 5 above, except unitized fence and the muter as described before so edge of workpiece sl_ould be held flush against that outer most curling edge of bit is aligned witll Ilne face of fence and end to be cut should be resting "A"...
- Page 16 USING ROUTER TABLE WITHOUT THE UNITIZED For maximum accuracy, one edge of your workpiece FENCE (edge sliding againsl the fence)-rhust be true and slraight. Set up your fence as follows: WARNING: ROUTING WITHOUT THE UNITIZED 1. Raise guard and rest it against the back o! the FENCE AND THUS THE GUARD COULD CAUSE vacuum outlet.
- Page 17 I1t1:1%.4..ILLI;Jt I,,'_ _IIVI;Illl !.1111;I L.II_.II;;II.II,._/I I0., I_.I l_l_.-J .-_s|_t,,.'_ being cut, then feed from LEFT TO RIGHT as stlown in away from the _arting pin, as shown by position #3 i_ Figure 37. Figure 39. 6. At this point, the piloted router bit is acting as a guide and not the slatting pin.
- Page 18 Notes...
- Page 19 3.,_1 I I Ij,25 • ._:= _,19 Part No. Quan. Descdpllon Part No. Descrtptlt]n Quan. 2gLCN-753 RouterTable 21_.-651 Clamp F_od 29LCN-755 29L-652 Clamp Pl_,_e Table leg 29A-306-14 3/4OD x 913210Washer 29A-246-12 1t4-20x I Ig Hex Head Cap Screw 2gA-310-7 29GD-321 1/4 Washer Cap Push Nut 1/4-20 x I-3,/4 Ig CarnageBolt 29A-242-12...