Download  Print this page

Craftsman 875.191180 Owner's Manual page 2

Pneumatic 1/2" drive impact wrench
Hide thumbs
   

Advertisement

Read Operating Instructions
Please become familiar with all the instructions
and
warnings before operating any pneumatic tool.
Always Wear Approved Eye Protection
Impact resistant eye protection should meet or exceed
the standards set forth in ANSI Z87.1, Occupational and
Educational Eye and Face Protection. Look for marking
Z87.1 on your eye protection to ensure that it is an
approved style.
Hearing Protection is Recommended
Hearing protection should be used when the noise level
exposure equals or exceeds an 8 hour time-weighted
average sound level of 85dBA. Process noise, reflective
surfaces, other tools being operated nearby, all add to the
noise level in a given work area. If you are unable to
determine your noise level exposure, we recommend the
use of hearing protection.
Avoid Prolonged Exposure to Vibration
Pneumatic tools can vibrate during use. Prolonged
exposure to vibration or very repetitive hand and arm
movements
can cause injury. Discontinue the use of any
tool if you experience
tingling, numbness, discomfort or
pain in your hands or arms. You should consult your
physician before resuming use of tool.
90 PSI Maximum
This tool is designed to operate at an air pressure of 90
pounds per square inch gauge pressure (90 PSI)
maximum, at the tool. Use of higher air pressure can, and
may cause injury. Also, the use of higher air pressure
places the internal components
under loads and
stresses they were not designed for, causing premature
tool failure.
NOTE: THE AIR SUPPLY SHOULD BE CLEAN, DRY AND
PREFERABLY LUBRICATED. FOR BEST RESULTS
DRAIN THE MOISTURE FROM YOUR COMPRESSOR
DAILY
Use Only Impact Sockets & Accessories
Only use sockets designated "FOR USE WITH IMPACT
WRENCHES," Hand tool sockets can break, creating a
hazard from flying pieces, Always check sockets,
retainers and drives regularly for wear or damage and
replace when necessary,
[ WARNINGI
Some dust created by power sanding, sawing, grinding,
drilling and other construction
activities contains chemi-
cals known to cause cancer, birth defects or other
reproductive
harm. Some examples of these chemicals
are:
Lead from lead based paint
crystalline
silica from bricks and cement
and other masonry products, and
arsenic and chromium from chemically-
treated lumber.
Your risk from those exposures varies, depending on how
often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work
with approved safety equipment,
such as dust masks that
are specifically designed to filter out microscopic
par-
ticles.
(2)
FULL TWO YEAR WARRANTY ON
CRAFTSMAN AIR-DRIVE TOOLS
If this Craftsman tool fails to give complete satisfaction
within two years from the date of purchase, RETURN IT
TO THE NEAREST SEARS STORE IN THE UNITED
STATES, and Sears will repair it free of charge. If this
Craftsman tool is used for commercial or rental
purposes, this warranty applies for only 90 days from the
date of purchase. This warranty gives you specific legal
rights, and you may also have other rights which vary
from state to state.
Sears, Roebuck and Co. Dept. 817WA, Hoffman
Estates, IL 60179.
The Craftsman Model 875.1911801/2" Square Drive
Impact Wrench is ideal for general assembly,
automotive, agricultural and industrial applications.
Features
Built-in regulator for power output adjustment.
Pin type clutch for increased power output.
Ring-type socket retainer allows quick socket
changes.
Specifications
Drive size ............................................................................... 1/2"
Impacts per minute ..................................................
1,300 IPM
Free speed (No Load) ........................................... 7 000 RPM
Ultimate torque .......................................................
230ff. Ibs.
Weight ............................................................................. 4½ Ibs.
Overall length ....................................................................... 7Y2"
Average air consumption ..............................................
5 CFM
Recommended hose size ........................................... 3/8" I.D.
Air inlet.......................................................................... 1/4"NPT
Maximum Air Pressure .................................................. 90 PSi
Pre-Operation
Before the tool is connected to the air supply, clear the air
hose of accumulated
dust and moisture by running air
freely through the air hose for 5-10 seconds,
Before
removing a tool for service or changing sockets, make
sure the air line is shut-off at the compressor, This will
prevent the tool from operating if the throttle is accidenBy
engaged.
Installation
(See figure
1)
This tool is designed to operate at 90 psi, Lower pres-
sure (below 90 psi) will reduce performance of the tool
while higher air pressure (over 90 psi) raises the perfor-
mance of the tool beyond its rated capacity and could
cause serious damage to tool and user.
Always use clean dry air. Excessive moisture and dirt will
greatly reduce the life of any air motor. We recommend
the installation of an in-line filter-regulator-lubricator
as
close to the tool as possible.
A 3/8" air hose is required up to a length of 8 ft. If more
length is required a 1/2" air hose should be used at the
compressor.
Attach a 3/8" whip hose for the remaining
4 - 8 ft. for flexibility. Be sure all hoses and fittings are the
correct size and tightly secured before using air tool.

Advertisement

Table of Contents
loading

  Related Manuals for Craftsman 875.191180