Table of Contents
Advertisement
UNPACKING
This product
requires
assembly.
IJ Carefully
lift saw from the carton
and place it on a level
work sudace.
NOTE:
This too! is heavy.
To avoid back
injury,
keep
your
knees
bent and lift with your legs,
nat your
back,
and get help when
reeded.
19 Inspect
the took carefully
to make sure no breakage
or
damage
occurred
during
shipping.
E1 Do not discard
the pacldng
material
until you have
carefully
iospected
and satbfaetobty
operated
the tool.
The saw is factory
set for accurate
cutting.
After
assembling
it, check
for accuracy.
If shipping
has
influenced
the settings,
refer' to specific
procedures
explained
in this manual
El if any parts are damaged
or missing,
please
can
1-800-932-3188
for assistance.
_
WARNING:
If any parts
are missing,
do not operate
this tool until the missing
parts
are replaced.
Failure
to do so could
result
in possible
seric)us
personal
injury.
_
WARNING:
Do not attempt
to modify
this tool
or create
accessories
not recommended
for use
with this tool
Any such
alteration
or modification
is
misuse
and could
resull
in a hazardous
condition
leading
to possible
serious
personal
injury.
_
WARNING:
Do not connect
to power
supply
until
assembly
is complete.
Failure
to comply
could
result
in accidental
starting
and possible
serious
personal
injury.
,_,_"_ WARNING:
Do not lift the saw without
help. Hold
it close
to your
body.
Keep your
knees
bent
and
lift with your legs,
not your back.
Ignoring
these
precautions
can ,esult in back
injury.
_
WARNING:
Never stand
directly
in line with the
blade
or allow hands
10 come
closer
than 3 in. to the
blade.
Do not reach
over or across
the blade
Failure
to heed this warning
can result
in serious
personal
illlLiry.
A
WARNING:
To avoid
serious
personal
injury,
always
make sure the table
saw is securely
mounted
to
a workbench
or an approved
leg stand
NEVER
operate
the saw on the floor.
MOUNTING HOLES
This toot comes
mounled
to a leg stand.
]f you chose
remove
the leg stand,
the table
saw must
be mounted
firm _upporfing
surface
such as a worl_bench
or leg sin _d,
Four
bolt holes
have been
provided
in the saw's
basel
this porpose.
Each of the four mounting
holes should
b
boll_
securely
using
3/8 in. machine
botts,
lock wash_
and Nex nuts (not included).
Bolls
should
be of sufficiei
t
length
to accommodate
the saw base,
lock washers,
I_ _x
nuts, and the thickness
of the workbench.
Tighten
all < ur
bolts
securely.
Carefully
check
the workbench
after mounting
to make
sure that
r_o movement
can occur
du[ng
use. If any tip
ping, sliding,
or we kirlg is noted,
secure
the workberi
to
the fleer
before
operating.
TO INSTALLTHE
BEVEL
HANDLE
ASSEMBL
I
See Figure
6.
I
r_ Lift the end cap off the bevel handle
assembly
using I a
flu i blade
screwdriver.
/
Ea Hdld [he nylon nut securely
and turn
the screw
couoler-
clockwise
to remove
the nut completely
I
NOTE:
Do not remove
tile screw
from the handle
o:rlthe
washer
from the end of [he screw.
i
/
Place the nylon
nut into the recessed
hole on the ba_,k
of ihe heightibevel
adjusting
handwheel
arid hold
in/
pl_ce,
l
[] Slide the handle> screw,
and washer
into the hole on I[he
height/bevel
ad _eting
handwheeh
/
B Using
a flatlqead
screwdriver,
iul n the screw
clockwise
and tighten
in place.
/
[] Push
the end cap back
in place
on the end of the
handle.
NUT
BEVEL
ftEIGItTIBEVEL
HANDLE
ADJUSTINGftANBWHEEL
Hide quick links:
Advertisement
Table of Contents
