Usingdspmodes - JVC RX-ES1SL Instructions Manual

Creating realistic sound fields
CENTER*_: To adjust the center speaker output level
(from -10 dB te +10 dB).
SURR L*_: To adjust the left surround speaker output level
(from -10 dB te +10 dB).
SURR R*': To adjust the right surround speaker output level
(from -10 dB te +10 dB).
PANORAMA control*2:
• Select "ON" when you wou{d like to enjoy
"wraparound" sound effect with side-waft image.
• Select "OFF" when you would like to hear
originally recorded sound.
* "0" is the initial setting for each speaker setting.
*2 "OFF" is the initial setting.
6 Turn MULTI JOG to adjust the item selected in
step 5, then press SET.
Your setting is stored.
• When adjusting the speaker output levels, make adjustments so
that the sound level of the selected speaker is set at the same
level as that of the front speakers.
L_. m _ []D_LII
............ i:: . ... 8 2n
I *.. N
"r'
.+.
-- , ...... !,._ .
Ex.: When selecting "+8 (dB)" for "CENTER."
7 Repeat steps 5 and 6 to adjust the other
settings.
To cancel Surround mode
Press SURROUND repeatedly on the remote control or press
SURROUND then turn MULTI JOG on the front panel so that
"STEREO" appears on the display.
• If Surround mode is canceled while playing back multi-channel
digital software, all channel signals are mixed and output through
the front speakers (and subwoofer if you have connected a
subwoofer and set the subwoofer setting corrsctiy--"USE" for Quick
Setup or "YES" for Manual Setup_see pages f 6 and 17).
• You can adjust the speaker output levels using the remote control
without outputting the test tone.
• You cannot adjust the center speaker output level and no test tone
comes out of the center speaker when "CNTR SP" is set to "NO."
• You cannot adjust the surround speaker output levels and no test
tone comes out of the surround speakers when "SURR SP" is set
te "NO."
• Remember not to change the speaker setting while using any
Surround modes; otherwise, the Surround mode may be canceled
when you deactivate the speakers required for it.
• You cannot use any Surround modes when selecting DVD MULTI
as a playback source.
UsingDSPmodes
Once you have adjusted the DSP modes, the adjustment is
memorized for each source.
• You cannot use the DSP modes if no surround speakers are
connected.
• You cannot adjust the effect level for"ALL CH ST."
When operating this receiver using the remote
control, always set the mode selector to
AUDIO/TV/VCR/DBS,
Before you start, remember...
Make sure that you have set the speaker information correctly (see
pages 15to 18).
Fromthe remote control:
it will be convenient for you to use
the remote control for the sound
adjustments, since you can make
adjustments from your listening
point, and use the test signak
1 Start playing 2 channel software--either Linear
PCM or analog signal--and select the source.
2 Press SURROUND repeatedly until one of the
DSP modes you want to apply appears on the
display.
The DSP indicator lights up on the display.
• Each time you press the button, the DSP modes change as
follows:
R
L_c_ su_wF_ _P ...............
, ,,,,-, ,', ;n
L=..L %." I=_/_\ z.=.I== z...z LJ w
LIVE CLUB --_ DANCE CLUB
HALL--_ PAVtLION /
ALL CH ST. _ STEREO (Surround!DSP off)
(Back to the beginning) J
3
Press TEST to check the speakers output
balance.
"TEST L"starts flashing on the display, and a test tone comes out
of the speakers as follows:
__ _ . ."..2 .....
_TEST L --_ TEST C --_ TEST R'_n
I (Left front speaker) (Ce0!er speaker)(Righ t fron t speaker) I /
1_ TEST LS -_ TEST RS
(Le t surround speaker) (R ght surround speaker j
CONTINUED ONTHENEXTPAGE
29