Table of Contents
Advertisement
Quick Links
MODEL NO.
757.242330
Caution:
Read Rules for
Safe Operation
and Instructions
Carefully
-
i
n,,lU,,,i
,,iru,,_l
®
10qNCH
MOLDBOARD
PLOW
FOUR 55 POUND WHEEL WEIGHTS, ONE FRONT WEIGHT
BRACKET, AND A SLEEVE HITCH ACCESSORY ARE RE-
QUIRED FOR OPERATION
ALSO, TIRE CHAINS ARE
RECOMMENDED
® Assembly
® Installation
® Operation
® Repair Parts
,,it,
i ,n
..............
inlll,l,l,,,
'11'
1:
ilU,irll
nl,
.....................
L-1222 SC
Sears, Roebuck And Co,
Hoffman Estates, tL 60179, USA,
ilU,i
i,i ,,,lit
i
lU...................
i lU,l,,
i
lUUl
i
Advertisement
Table of Contents
Related Manuals for Craftsman 757.242330
Summary of Contents for Craftsman 757.242330
- Page 1 n,,lU,,,i ,,iru,,_l MODEL NO. 757.242330 ® 10qNCH MOLDBOARD PLOW FOUR 55 POUND WHEEL WEIGHTS, ONE FRONT WEIGHT Caution: BRACKET, AND A SLEEVE HITCH ACCESSORY ARE RE- Read Rules for QUIRED FOR OPERATION ALSO, TIRE CHAINS ARE RECOMMENDED Safe Operation and Instructions Carefully ®...
-
Page 2: Limited One-Year Warranty
LIMITED ONE YEAR WARRANTY ON MOLDBOARD PLOW For 1 year from the date of purchase, when this Moldboard Plow is maintained and lubricated according to the operating and maintenance instructions the owner's manual, Sears will repair, free of charge, any defect in material or workmanship.. - Page 3 CONGRATULATIONS on your purchase of a Sears Craftsman 10" Moldboard Plow It has been designed, engineered, and manufactured to give you the best possible dependability and performance Should you experience any problem you can not easily remedy, please contact your nearest...
- Page 4 Z-1216-A HARDWARE 1 Bo]674P Hex ILocM Nut 5/16 3 Used No 26 P-597 Spacer 5/8t D x 1/2 2 Used No 35 15Mt632P No 3 B-1678F _ No 29 1M1628P Plow Bolt Hex (Lock) Head Bo_t x 2' 1M1624P 2 Used 1/2' x 1_3/4"...
- Page 5 Z-1216-C HARDWARE No 6 P-172P NO 24 Coulter Axle Coulter Clamp 1 Used. Used No 23 P-386P "U" Bolt 1 Used ASSEMBLY NOTES Tools Required For Assembly: IT IS RECOMMENDED THAT YOU CAREFULLY READ THIS OWNER'S MANUAL BEFORE STARTING ASSEMBLY OF THE UNIT 1-10"...
- Page 6 1/2" x 2" Ptow bott PLOW BOTTOM AND STANDARD 1/2"X1-1/2" Referto Fig.2 Carriage bolt Standard @Assemble the landside to frog usingtwo 3/8"x 1" plow boltsand 3/8" hex nuts. @ Attachstandard to frog using 1/2"x2" plow bolt Landside and 1/2" hex nut as shown, ©...
-
Page 7: Operation
OPERATION PREADJUSTMENT [Refer to Fig. 5 and 6] Note: During normal plowing, the right side Tractor Wheels will be riding in the previously plowed furrow A furrow is the cut area your plow makes when turning the soil, An initial setting for your plow is required to cut the first furrow on level ground The following pre-sets will... - Page 8 PLOWING TIPS e Highweedsor grassmustbe cut downwith a Lay out your field to be plowed, and if rotarymowerbeforeplowing, possible make it rectangular in shape e NEVER plow whensoil is wet+A ruleof thumb Note: It is easier to plow a few long furrows is to pick up a handfulof soil androll it into than many short ones, Leave some room at each a "ball"...
-
Page 9: Depth Adjustment
DEPTH ADJUSTMENT Referto Fig 8 TURN CLOCKWISE Depth Crank eTo turnthe plowshareinto the groundto 'TO INCREASE PLOW DEPTH openthe "first"furrow,adjustthe pointdownward untilthe plowis cutting4"to5" deep FIG, e Aftera few furrows, (or desired depthis reached) t urn thecrankCOUNTER-CLOCKWISE maintain thatdepth Do not allowlandside to ride J4URN COUNTER-CLOCKWISE morethan !/2"... -
Page 10: How To Order Repair Parts
TROUBLE SHOOTING [PLOWING DIFFICULTIES AND REtVIEDIESI PROBLEM CAUSE/CONDITION REMEDY ® Improper Crank Adjustment. Refer to Depth Adjustment and turn crank CLOCKWISE t or 2 turns at a time. e Badly worn Plow Share. Replace with a new Share. SLOW GROUND ENTRY e Ground extremely dryand Add extra weight to tractor... - Page 11 MOLDBOARD PLOW MODEL NUMBER 757.242330 PRinTED iN U S A 27 25 PARTS LiST Ref_ Re|° Qty,, Part No Description No,, PartNo° Description Qty,, Coulter Clamp P-387-01 B-1674P Hex Lock Nut, 5/16" P-596-10 Hex Lock Nut, t/2" Adjljsting Bracket B-1677P P-597 Hex Lock Nut, 5/8"...