Table of Contents
Advertisement
PLOW BOTTOM AND STANDARD
Referto Fig.2
@Assemble the landside to frog usingtwo 3/8"x 1"
plow boltsand 3/8" hex nuts.
@ Attachstandard to frog using 1/2"x2" plow bolt
and 1/2" hex nut as shown,
© Insertthe 1/2"x 1_1/2"carriagebott throughfrog
andstandardandsecurewith a 1/2" hex nut.
@ Insert o ne1/2"x I-1/2" HexBott(Tracking
AdjustingBolt)throughthe "tab"atthe bottom
of standard.Placethe 1/2" Square nut between
the 'q'ab"andFrog,andthreadthe Tracking
AdjustingBolt into the squarenut untiltight,
Tightenall fasteners securely.
PLOW
FRAME
AND
BOTTOM (Refer to
Fig
3]
e Straddle
the beams over standard and fasten together
at the LOWER hole in the standard with one 1/2"x 1-3/4"
bolt and 1/2" hex lock nut
e Attach end of threaded
tube to side of standard at
the UPPER hole with a 1/2"x 1-1/2" hex bolt followed
by
the 1/2" flat washer, then place the 9/16"spacer
in the
hole in standard and secure this assembly with one 1/2"
hex lock nut
e Tighten these fasteners so that the threaded
tube is
free to pivot
COULTER
BLADE
(Refer to Fig 4]
e Insert coulter
standard
into fork, align the holes and
drive the 5/t6"x
1-1/4" pin through,
leaving an equal
amount of pin on each side
e Attach the coulter hub to the coulter blade using
three 5/16"x
3/4" carria£;e bolts, 5/16" flat washers, and
5/16" lock nuts
e Install the coulter
blade on the fork by inserting
the axle through
one leg of the fork, the coulter
hub, and other leg of fork,
Secure with the two 5/8" flat
washers and 1/8"x
1-1/4" cotter pin, bend the legs over°
e Attach the coulter assembly to the plow beam as
shown, using the "U" bolt, coulter clamp, two spacers
(locate BETWEEN the plow beams), and secure with two
5/8"
hex nuts
Q Position the coulter
standard between the "U" bolt and
coulter
clamp and move up to the highest position
eRefer to the coulter adjustment
section
for proper set-
ting, to be adjusted AFTER you begin plowing,
_
WARNING
O The "Attachment Clutch" Switch on dash of Tractor
(device that engages Tractor Mower) needs to be
ENGAGED at afl times while operating Tractor
This
actuates the Operators Sensing Device in the Tractor
seat ---Tractor Engine wil! stop in case you dismount
or fall off Tractor
Failure to actuate this device
can cause personae injury or damage to your Tractor
and Property if you were to fatl off, SWITCH MUST BE
DISENGAGED IN ORDER TO RESTART ENGINE!
1/2" x 2" Ptow bott
1/2"X1-1/2"
Carriage
bolt
Standard
Landside
/
1/2" Square nut
1/2"× 1-1
He× bolt-
!/2"Hex
nut
(Tracking
Ad
3/8" Hex nuts
FIG 2
Threaded
tube
Standard
___..
Crank
1/2"1D
x9/16
Spacer
l/2'
.I_-_,.
1/2- Lock nut
Fiat washer
t
1/2"x 1-t/2'
Hex Bolt
tube
1/2" Lock nut
1/2" x 1-3/4"
Hex Bolt
Lower hole in standard
FIG. 3
5/8"1D
× 1/2" Spacers _'l
"U" Bolt
Ptew Beam _'_'_-
""_©
5/16"X3/4"
Carriage
bott
-Coutter
clamp
5/16"
Locknut
Cotter pin
i
Coulter
standard
I
/8
5/t6
x t-1/4"
Pin
Flat wa,sher
Coulter
fork
_-_
Coulter
blade
FIG. 4
Advertisement
Table of Contents
