Adjust The Image; Turning Off The Projector - Epson PowerLite 30C Quick Setup Manual

3
Set up the remote control
Pull out the insulating tape that protrudes from
the battery holder.
The remote control
is ready for use.
4
Plug in and turn on
1
Remove the lens cover.
2
Connect the power cord to the
projector and plug the other end
into a grounded outlet.
The power light turns orange.
3
Turn on the other equipment
connected to the projector.
4
Press the Power button on
the projector or remote control.
The power light flashes green,
and the projector lamp comes on
in about 15 seconds.
5
Start your video. If you have connected
more than one video source, press the
Computer or S-Video/Video button on
the remote control to select the one
you want to watch.
Note: If you connected a laptop computer and no
image is being projected, you may need to set
up the laptop to output signals externally. See
your laptop's documentation for instructions.
For additional instructions on connecting to a
computer, see your User's Guide on the CD-ROM.

Turning off the projector

1
When you're finished using the projector, first turn off the video source.
2
Press the Power button on the projector or remote control.
3
When you see the confirmation message, press the
The power light flashes orange as the projector cools down.
Caution: Never unplug the projector when the
flashing orange.
EPSON is a registered trademark of SEIKO EPSON CORPORATION. PowerLite is a registered trademark of Epson America, Inc.
General Notice: Other product names used herein are for identification purposes only and may be trademarks of their respective owners.
EPSON disclaims any and all rights in those marks. Copyright © 2002 by Epson America, Inc. Printed in USA. 8/02
Power
Computer S-Video/Video Color Mode
Source buttons
Menu A/V Mute Freeze
E-Zoom
Enter
Auto ESC
Power button again.
power light is green or
Multipurpose Entertainment Projector
EPSON ® PowerLite
5

Adjust the image

1
If you need to raise the image,
press the foot adjust buttons
and lift the front of the projector.
Release the buttons to lock the
feet in the position you want.
If you need to straighten the
image, raise or lower an
individual foot.
2
Rotate the focus ring to sharpen the
image.
3
If your image is upside-down
or reversed, you need to change
the setting in the Advanced menu.
Press the Menu button on the
remote control and use the Enter
button to choose the Advanced
menu. Then select the correct
setting for your setup.
4
If a computer is connected, do this after projection starts. Press the
Menu button on the remote control, and use the Enter button to
choose the Video menu. Go to the Input Signal option and change
it to RGB.
5
If your image looks like
the screen squarely. Then, if necessary, press the Keystone button on the
projector's control panel until the image is corrected. (You also can do this
using the projector's Setting menu. See your User's Guide on the CD-ROM.)
6
To select the best color mode, press the
Color Mode button on the remote control
repeatedly to move through the options.
7
To boost the projection quality of films, first
attach the EPSON cinema filter to the lens.
Then, press the Menu button on the remote
control, go to the video menu, and change
the EPSON Cinema Filter setting to ON.
See your User's Guide on the CD-ROM for more
information about image adjustments.
If you see a blank screen
If you see a blank screen or the No Signal or
Not Supported message, check the following:
• Make sure the lens cover is off.
• Make sure your power cord and
video cable are connected securely.
• If the power light is orange, press the
either the remote control or the projector's control panel.
• Make sure the correct input source is selected. On the remote control,
press the Computer or S-Video/Video button to change the image
source. Or, press the Source button on the control panel.
• Try turning off your video equipment or computer and restarting it.
• If mute mode is active, press the A/V Mute button on the remote
control to resume projection.
• If you connected a computer to the projector, it may be necessary
to change the image signal to the projector. See "Troubleshooting"
in your User's Guide on the CD-ROM.
® 30c
or , first make sure the projector is facing
Power
Computer S-Video/Video Color Mode
Menu A/V Mute Freeze
E-Zoom
Enter
Auto ESC
No signal ( Help )
?
Power button on
Color Mode
button
CPD-14798