Download  Print this page

Kenmore 625.385010 Owner's Manual page 9

Advanced two-stage drinking water fiter
Hide thumbs

Advertisement

FAUCET
ELECTRONICS
inside the faucet base is a battery operated
6 month
timer.
See Figure 14.
An amber LED indicator
is also located in the front of
the faucet base.
This LED will flash continuously
after 6
months
has passed.
This indicates
that it is time to
replace the battery and filter cartridges.
CHANGE
BATTERY
To change (or install) the battery, complete
the following
steps.
1. Loosen the screw on the right side of the faucet base
See Figure
14.
2. Press the battery
housing
upwards
from the front
faucet base until it releases
from the faucet base.
See
Figure 14.
3. Replace (or install) the battery
(Maxell CR 2032 or
equivalent).
Place battery
into the holder with the
positive
(+) side facing the back of the holder.
4. When the battery is first replaced
it will flash six times
and turn off. This indicates
the battery is fully
charged.
After the six flashes, the timer enters the 6
month time cycle.
NOTE: If the LED repeatedly
flashes just two times, it is
not a fully charged
battery and will need to be replaced.
5. Re-install
the timer housing
and firmly tighten the
mounting
screw.
See Figure 14.
FILTER
CARTRIDGE
LIFE
it is recommended
to replace the battery
and filter car-
tridges every 6 months
of use. There are several vari-
ables that determine
how long a cartridge
will last.
These include:
1. How much water you use, and
2. How much sediment,
taste and/or
odor, or other
unwanted
substances,
are in the water.
Use the following
information
as a guide.
However
no
matter which type of cartridge
you are using, you will
know it is time to replace it when you first notice the
return
of unwanted
substances
in your water.
Kenmore
Elite Advanced
Two-Stage
Drinking
Water
Filter model 625.385010 with replacement
element
pack
42-34381 conforms
to NSF/ANSI 42 and 53 for the specif-
ic performance
claims as verified and substantiated
by
test data.
The rated capacity for this system is 280 gal-
lons (1060 liters) at a rated service flow of 0.5 gpm (gal-
lons per minute).
battery
housing
Cover
Turn to the left
to remove
Filter
Cartridge
1
Filter
Cartridge
2
Figure 15
FILTER
CARTRIDGE
REPLACEMENT
Complete
the following
steps to replace the cartridges:
1. Turn filter cartridge
to the left to remove cartridges
from
the filter heads.
See Figure 15.
2. Dispose of the old cartridges
in a proper
manner.
3. install new cartridges,
making
sure to insert cartridge
1 and 2 into the correct opening
(note the printing
on
the cover designating
"Cartridge
1" and "Cartridge
2"). Turn cartridges
to the right to re-attach
to the fil-
ter heads.
4. Remove and replace the timer battery.
See "Change
Battery"
above.
Taste and Odor Cartridges:
Filter cartridges
contain acti-
vated carbon, a black powder.
When new, open the fil-
tered water faucet and allow fine carbon particles
to
purge from the cartridge.
Close the faucet when you no
longer see the "fines" (carbon particulates)
in the filtered
water, or approximately
10 minutes.
Questions?
Call The Kenmore
Water Line 1-800-426-9345
or visit KenmoreWater.com
9

Advertisement

Table of Contents
loading

  Related Manuals for Kenmore 625.385010

This manual is also suitable for:

Elite 625.385010