Table of Contents
Advertisement
SAFETY
The following symbols are used throughout this
guide as indicated in their descriptions:
HAZARD INTENSITY LEVEL
There are three levels of hazard intensity identified
by signal words -WARNING, CAUTION and FOR
SAFETY. The level of hazard intensity is deter-
mined by the following definitions:
-
WARNING
Hazards or unsafe practices which
COULD result in severe personal injury or death.
-
CAUTION
Hazards or unsafe practices which could
result in minor personal injury or product or property
damaae.
FOR SAFETY: To Identify actions which must be
followed for safe operation of equipment.
The following information signals indicate potentially
dangerous conditions to the operator or equipment.
Read this guide carefully. Know when these conditions
can exist. Locate all safety devices on the machine.
Report machine damage or faulty operation immediate-
ly. Do not use the machine if it is not proper operating
condition.
For SAFETY:
DO NOT OPERATE MACHINE:
Unless Trained and Authorized
Unless Operation Guide is Read and
understood.
In Flammable or Explosive areas.
WHEN USING MACHINE:
Go slow on grades and slippery
.
surfaces
Use care when backing machine.
Do not carry riders on machine.
Always follow basic safety and
traffic rules.
BEFORE LEAVING OR SERVICING
MACHINE:
Stop on level surfaces.
Turn off machine.
WHEN SERVICING MACHINE:
Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves when working on
machine.
Block machine wheels before jacking
machine up.
Use hoist or jack of adequate capacity
lift machine.
Use Windsor approved replacement parts.
4
WHEN TRANSPORTING MACHINE
I N A TRAILER:
Make sure the ramp angle i s no more than
and the ramp is strong enough to
support the machine.
Make sure ramp is clean and dry.
Put ramp into position.
Remove squeegee assembly & brushes
before loading.
Align the machine on a level surface ten
(10) feet behind the ramp.
Push machine up ramp carefully.
Securelv fasten the machine to the trailer.
THIS PRODUCT IS FOR COMMERCIAL USE ONLY.
EL ECTRICA
In the USA this scrubber operates on a standard 15 amp 11 5
volt A.C. power circuit (120V nominal). Special voltage mod-
els are available for international applications. The amp,
hertz, and voltage are listed on the data label found on each
machine. Using voltages above
the data label will cause serious damage to the motors.
GROUNDING INSTRUCTIONS:
This appliance must be grounded. If it should malfunction or
break down, grounding provides a path of least resistance
electric current to reduce the risk of electric shock. This ap-
pliance is equipped with a cord having an equipment-ground-
ing conductor and grounding plug. The plug must be inserted
into an appropriate outlet that is properly installed and
grounded in accordance with all local codes and ordinances.
Improper connection of the equipment-grounding con-
ductor can result in a risk of electric shock. Check with
a qualified electrician or service person if you are in
doubt as to whether the outlet is properly grounded. Do
not modify the plug provided with the appliance
not fit the outlet, have a proper outlet installed by a qual-
ified electrician.
This appliance is for use on a nominal 120-volt circuit, and
has a grounded plug that looks like the plug in "Fig. A" below.
A temporary adaptor that looks like the adaptor in "Fig. C
below may be used to connect this plug to a 2-pole receptacle
as shown in "Fig. B" below. The temporary adaptor should
be used only until a properly grounded outlet (Fig. A) can be
installed by a qualified electrician. The green colored rigid
ear, lug, or the like extending from the adaptor must be con-
nected to a permanent ground such as a properly grounded
outlet box cover. Whenever the adaptor is used, it must be
held in place by a metal screw.
NOTE: Check local electrical codes before using an
to
adaptor. Adaptors are not allowed in Canada.
98447 7/1/97
L:
or
below those indicated on
for
if it will
Hide quick links:
Advertisement
Table of Contents
