Chapter 9 Error Code List - Brother BES-963 Instruction Manual

Chapter 9 Error code list

Code Error Messages
E-00 ERROR 00
E-01 ERROR 01
E-02 Overtravel
Stop SW was pressed during
E-03
home positioning
E-04 Zero positioning is out of range
E-05 Needle stop position error
E-06 Needle bar case position error
E-07 Needle case lock
Stop while needle bar case
E-08
transferring
E-09 X-axis home position error
E-0A Thread breakage error
E-0B ERROR 0B
E-0C ERROR 0C
E-0D ERROR 0D
E-0E ERROR 0E
E-0F ERROR 0F
E-14 Y-axis home position error
E-15 Press for reatart.
E-16 ERROR 16
E-17 ERROR 17
X-axis stepping motor connector
E-18
error
E-1A ERROR 1A
E-1B ERROR 1B
E-1C Restart perimeter
Stop while transferring to next
E-1D
repeat pattern
Remove unused presser foot, or
E-1E
it may be damaged
E-1F Presser foot down error
162
Error
No error occurs.
Either motor of main shaft, X- or Y-axis, or lower
shaft has locked.
Overtravel occurs during home position detect-
ing movement.
The stop switch is pressed during home position
detecting movement.
Zero detecting movement out of range
Needle stop position error
Needle bar case position error
Needle bar case lock
Stop switch or emergency switch was pressed
while the needle bar case is traveling.
X-axis home position detection error
Thread breaking error
Stop or emergency stop during sewing
Insufficient bobbin thread
The machine does not return to the home position.
Mending finish
Undefined error
Y-axis home position error
Stop error during SSP processing (when press-
ing the stop key while the hoop is moving)
Needle with specified number is out of movable
area.
Speed Vol. No. is out of range.
X-axis stepping motor connector error
Destination coordinates error
The machine has reached the mending stop
position.
The machine stops during mask tracing.
The machine stops while the needle is moving
between patterns during repeat sewing.
Errors E-1C and E-1D are not displayed due to mechanical problems.
When the power is turned on, bed can not be
retracted.
Presser foot down error while searching for
home position just after the power is turned on.
BES-963BC • BES-1263BC
Measures
This is not usually displayed.
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the area sensor is faulty.
Press the or turn on the F/B switch on the head to either
STOP
side to restart the home position detecting movement again.
Turn the power off and on once. If the same error occurs
again, the home position sensor is faulty.
Adjust the pulley stop position (100 degrees) above the
needle and press the or turn on the F/B switch on the
STOP
head to either side.
This is not usually displayed.
Press the or turn on the F/B switch on the head to either
STOP
side. If the same error occurs again, the color change
mechanism is faulty.
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the X-axis mechanism is faulty.
After passing through the thread, press the
F/B switch on the head to either side.
This is not usually displayed.
This is not usually displayed.
This is not usually displayed.
This is not usually displayed.
This is not usually displayed.
Turn the power off and on once. If the same error occurs
again, the Y-axis mechanism is faulty.
Hoop movement restarts if you press
This is not usually displayed.
This is not usually displayed.
Turn the power off and on once after checking to see that the
connector of the X-axis stepping motor is properly connected.
This is not usually displayed.
This is not usually displayed.
Tracing is cancelled if the key is pressed when the ma-
STOP
chine is stopped during mask tracing. Press the
continue tracing.
This is displayed when the stop switch is pressed while the
hoop is moving. Press the to move the hoop again. (It is
necessary to press the again to start sewing.)
This is displayed when every other head control is selected
or when the bed is retreated (including when the power is
turned on). Remove the presser foot of the retreating head
and press the return key or turn the F/B switch of the head to
either side. If every other head control is not selected or the
bed is not retreated, the bed sensor position may be faulty.
Readjust it. Press the key. If the same error occurs
STOP
again, adjust it with the presser foot switch.
Press the or turn on the F/B switch on the head to ei-
STOP
ther side. If the same error occurs again, adjust the
presser foot switch.
or turn on the
STOP
.
key to