Table of Contents
Advertisement
FRAMING SPECIFICATIONS CONTINUED
C
M
d o
l e
N
. o
G
H
C
G /
R
- D
5 5
G
H
C
G /
R
- D
5 6
Figure 6
B
A
4 IN.
(103 MM)
Figure 7
A
Figure 8
D
B
A
A
B
. n i
7 5
1
2 /
6 3
0 0
m
m
4 1
1 6
9
4 1
. n i
5 6
3
4 /
0 4
3
4 /
0 0
m
m
6 1
0 7
0 1
5 3
Corner Installation
Note: If the Outside Combustion
Air Kit is to be installed, it must
be installed before the appliance
is framed and enclosed in the
finishing walls.
M
d o
l e
G
H
C
G /
R
G
H
C
G /
R
4 IN.
(103 MM)
Inside Chase Installation
Note: If the Outside Combustion
Air Kit is to be installed, it must
be installed before the appliance
is framed and enclosed in the
finishing walls.
M
d o
l e
G
H
C
G /
R
B
G
H
C
G /
R
Outside Chase Installation
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Note: If the Outside Combustion
Air Kit is to be installed, it must
be installed before the appliance
is framed and enclosed in the
finishing walls.
C
D
0 4
3
4 /
9 2
0 1
5 3
7
7 3
6 4
1
2 /
2 3
7
8 /
1 1
1 8
8
5 3
N
. o
A
B
. n i
6 3
5 1
1
- D
5 5
0 0
m
m
9
4 1
3
4 9
. n i
0 4
3
4 /
8 1
- D
5 6
0 0
m
m
0 1
5 3
4
7 5
N
. o
A
B
. n i
6 3
5 1
- D
5 5
0 0
m
m
9
4 1
3
4 9
. n i
0 4
3
4 /
8 1
- D
5 6
0 0
m
m
0 1
5 3
4
7 5
TYPICAL INSTALLATION SEQUENCE
The typical sequence of installation follows,
however, each installation is unique resulting
in variations to those described.
1. Construct the appliance framing.
2. Route gas supply line to appliance location.
3. Position the appliance.
4. Install the vent system and exterior termina-
tion.
5. Field wire and install operating control switch.
Install optional Forced Air Kit, if required
6. Make connection to gas supply.
7. Install optional Outside Combustion Air Kit,
if required.
8. Install the logs and rockwool.
9. Install the optional glass doors/enclosure
panel, if required
10. Checkout appliance operation.
11. Spillage Test and Safety Limit Switch
Operation.
12. Adjust burner to ensure proper flame
appearance.
2 /
PRE-INSTALLATION NOTES
The fireplace may be installed directly on a
combustible floor or raised on a platform of an
appropriate height. Do not place fireplace on
carpeting, vinyl or other soft floor coverings. It
may, however, be placed on flat wood, ply-
wood, particle board or other hard surfaces,
extending the full depth and width of the appli-
ance. Be sure fireplace rests on a solid continu-
ous floor or platform with appropriate framing
for support and so that no cold air can enter the
room from under the fireplace.
The fireplace may be positioned and then the
framing built around it, or the framing may be
1
2 /
constructed and the fireplace positioned into
the opening.
Usually, no special floor support is needed for
the fireplace, however, to be certain:
1. Estimate the total weight of the fireplace
system and surround materials such as brick,
stone, etc., to be installed.
7
Hide quick links:
Advertisement
Table of Contents
