Advertisement
Quick Links
Advertisement
Related Manuals for Stairmaster FreeClimber 4400
Summary of Contents for Stairmaster FreeClimber 4400
- Page 1 FREE CLIMBER 4400 ASSEMBLY INSTRUCTIONS 27694B...
-
Page 2: Tools Required
ASSEMBLY INSTRUCTIONS TOOLS REQUIRED: •CLAW HAMMER •KNIFE •1/2” WRENCH OR SOCKET 1. USE KNIFE TO REMOVE ALL PLASTIC STRAPS FROM AROUND PALLET AND CARTON. STRAP 2. USE CLAW HAMMER TO REMOVE STAPLES HOLDING CARTON TO PALLET. STAPLE LOCATION... - Page 3 ASSEMBLY INSTRUCTIONS 3. REMOVE PLASTIC COVER FROM STEPPER UNIT. PLASTIC COVER 4. USE CLAW HAMMER TO REMOVE WOODEN BLOCKS FROM PALLET. USE KNIFE TO REMOVE TYRAPS. TYRAPS WOOD BLOCKS...
- Page 4 ASSEMBLY INSTRUCTIONS 5. REMOVE HANDLE ASSEMBLY AND TWO BUBBLE PACKS FROM PALLET. BUBBLE PACKS HANDLE ASSEMBLY 6. REMOVE PROTECTIVE WRAP FROM HANDLE ASSEMBLY AND LAY ASIDE FOR FUTURE INSTALLATION. PROTECTIVE WRAP...
- Page 5 ASSEMBLY INSTRUCTIONS 7. OPEN SMALL BUBBLE PACK, IT CONTAINS THE CONSOLE, MAGAZINE RACK, PLASTIC BAG OF HARDWARE, AND SPACER. CONSOLE MAGAZINE RACK BAG OF HARDWARE SPACER 8. OPEN LARGE BUBBLE PACK, IT CONTAINS THE LEFT AND RIGHT UPPER COVERS. UPPER COVERS...
-
Page 6: Flat Washer
ASSEMBLY INSTRUCTIONS 9. OPEN PLASTIC BAG OF HARDWARE AND EMPTY CONTENTS. PLASTIC BAG 10. THE PLASTIC BAG CONTAINS FOUR BOLTS AND 4 FLAT WASHERS. SLIDE THE FLAT WASHER OVER THE BOLT. BOLT FLAT WASHER... - Page 7 ASSEMBLY INSTRUCTIONS 11. THE PLASTIC BAG ALSO CONTAINS FOUR SCREWS, FOUR LOCK WASHERS, AND ONE RUBBER GROMMET. SLIDE LOCK WASHER OVER SCREW THREADS. THE PLASTIC RIVETS ARE REQUIRED TO SECURE THE UPPER COVERS. SCREW LOCK WASHER GROMMET 12. UNCOIL CABLE FROM AROUND FRAME NECK.
- Page 8 ASSEMBLY INSTRUCTIONS 13. GET HANDLE ASSEMBLY AND RUBBER GROMMET, SLIDE GROMMET OVER HANDLE. SLIDE HANDLE ASSEMBLY INTO FRAME NECK. NOTE ORIENTATION OF RUBBER GROMMET. RUBBER GROMMET NECK FRAME...
- Page 9 ASSEMBLY INSTRUCTIONS 14. MAKE SURE THAT THE HANDLE IS POSITIONED SO THE UPPER HANDLE PORTION IS PERPENDICULAR TO THE FLOOR UPPER HANDLE 15. GET THE FOUR BOLTS AND FLAT WASHERS, ALIGN HOLES IN HANDLE ASSEMBLY AND NECK FRAME. INSTALL BOLTS WITH 1/2” WRENCH OR SOCKET. MAKE SURE THE BOLTS ARE TIGHT.
- Page 10 ASSEMBLY INSTRUCTIONS 16. GET THE RIGHT HAND UPPER COVER, ROUTE CABLE THROUGH THE WHITE CLIPS, CLOSE CLIPS. CLIP CABLE RIGHT UPPER COVER 17. FOR STEPPERS WITH CONTACT HEART RATE CABLE, ROUTE CABLE FROM HOLE IN HANDLE TO TOP OPENING IN THE UPPER COVER.
- Page 11 ASSEMBLY INSTRUCTIONS 18. GET THE LEFT HAND UPPER COVER, SLIDE RUBBER GROMMET UP TO THE TOP OF THE HANDLE ASSEMBLY. POSITION THE RIGHT HAND UPPER COVER OVER THE LOWER COVER AND HANDLE POST. FIT RUBBER GROMMET INTO THE RIGHT HAND UPPER COVER. POSITION THE LEFT HAND UPPER COVER OVER THE LOWER COVER, HANDLE POST.
- Page 12 ASSEMBLY INSTRUCTIONS 20. GET CONSOLE AND MAGAZINE RACK.. POSITION BRACKET IN HOLES AND GROOVES ON THE BACK OF THE CONSOLE. CONSOLE HOLES IN BACK OF CONSOLE MAGAZINE RACK 21. GET SPACER AND POSITION OVER MAGAZINE RACK ON CONSOLE. CONSOLE SPACER MAGAZINE RACK...
- Page 13 ASSEMBLY INSTRUCTIONS 22. POSITION CONSOLE, SPACER, AND MAGAZINE RACK ON TOP OF THE UPPER COVERS. PLUG IN CONNECTOR FROM CABLE TO CONSOLE. BE SURE TO POSITION THE CONNECTOR CORRECTLY WITH THE ALIGNING TAB ON THE FEMALE CONNECTOR WITH THE ALIGNING SLOT ON THE MALE CONNECTOR.
- Page 14 ASSEMBLY INSTRUCTIONS 24. USE FOUR SCREWS WITH LOCK WASHERS TO SECURE CONSOLE TO UPPER COVERS. SCREWS 25. GET KNIFE AND REMOVE STRETCH WRAP FROM CONSOLE AND CARTON ATTACHED TO PEDAL. CONTENTS OF CARTON FOR 4400PT: BAG OF SPARE PLASTIC PUSH RIVETS RIVET REMOVAL TOOL MANUAL POWER SUPPLY...