EverFocus EHD360 Operation Instructions Manual
EverFocus EHD360 Operation Instructions Manual

EverFocus EHD360 Operation Instructions Manual

High resolution vandal proof weather resistant 3-axis ir dome camera

Advertisement

Please read this manual first for correct installation and operation. This manual should be retained
for future reference. The information in this manual was current when published. The
manufacturer reserves the right to revise and improve its products. All specifications are therefore
subject to change without notice.
PRECAUTIONS
1.
Do not install the camera near electric or magnetic fields.
Install the camera away from TV/radio transmitters, magnets, electric motors, transformers
and audio speakers since the electromagnetic fields generated from these devices may distort
the video image or otherwise interfere with camera operation.
2.
Never disassemble the camera beyond the recommendations in this manual nor
introduce materials other than those recommended herein.
Improper disassembly or introduction of corrosive materials may result in equipment failure
or other damage.
3.
Try to avoid facing the camera toward the sun.
In some circumstances, direct sunlight may cause permanent damage to the sensor and/or
internal circuits, as well as creating unbalanced illumination beyond the capability of the
camera to compensate.
4.
Keep the power cord away from water and other liquids and never touch the power
cord with wet hands.
Touching a wet power cord with your hands or touching the power cord with wet hands may
result in electric shock.
5.
Never install the camera in areas exposed to oil, gas or solvents.
Oil, gas or solvents may result in equipment failure, electric shock or, in extreme cases, fire.
6.
Cleaning
For cameras with interchangeable lenses, do not touch the surface of the sensor directly with
the hands. Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and
the camera lens. Use a damp soft cloth to remove any dirt from the camera body. Please do
not use complex solvents, corrosive or abrasive agents for cleaning of any part of the camera.
7.
Do not operate the camera beyond the specified temperature, humidity or power source
ratings. This camera is suitable for indoor and outdoor operation.
High Resolution Vandal Proof
Weather Resistant 3-Axis IR Dome Camera
EVERFOCUS

Operation Instructions

EHD360
Model No.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the EHD360 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for EverFocus EHD360

  • Page 1: Operation Instructions

    EVERFOCUS High Resolution Vandal Proof Weather Resistant 3-Axis IR Dome Camera Operation Instructions EHD360 Model No. Please read this manual first for correct installation and operation. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products.
  • Page 2: Package Contents

    Use the camera at temperatures within -10°C to +50°C (14°F to 122°F) and in an IP66 compliant environment; this device is not rated as submersible. The input power source is 12VDC. Be sure to connect the proper + / - polarity and voltage, as incorrect polarity or too high a voltage will likely cause the camera to fail, and such damage is not covered by the warranty.
  • Page 3: Specifications

    Camera Unit x 1 Mounting kit includes: -Screws x 4 -Security wrench for housing screws x 1 -Expanding Screws x 4 -Washers x 4 Operation Instructions (this document) x 1 Weatherproof bushing x 1 Power cable x 1 Video cable x 1 Power adapter pigtail (for NTSC model only) x 1 Mounting template x 1 SPECIFICATIONS...
  • Page 4: Installation Instructions

    DIMENSIONS Bottom View Dimensions Front View Top View Bottom View A. Lens E. Inner plate mounting holes B. IR-LED F. BNC Connector C. Side conduit entry G. DC Connector D. Back conduit entry INSTALLATION INSTRUCTIONS Drill the Holes 1. Locate the desired mounting location; position housing with camera pointed generally in the desired direction and mark location.
  • Page 5 3. Tighten the 4 mounting screws to secure the camera body to the mounting surface. 3. If you need to wire cable through side conduit hole, use a coin to remove the conduit plug; save the plug as it will be used to close the rear conduit hole. Back conduit hole Conduit plug...
  • Page 6 6. (Optional) Pass the power/video wire under the base plate and up through the center hole. 7. Position the power/video wire so that it does not interfere with the camera module and carefully attach the connector to the camera board, being sure to position the connector so it fit properly onto the tiny pins within.
  • Page 7: Everfocus Electronics Corp

    EverFocus USA - California: EverFocus USA - New York: 1801 Highland Avenue, Unit A, Duarte, CA 91010, 415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA TEL: +1 631 436 5070 TEL: +1 626 844 8888...

Table of Contents