Page 1 EPSON SureColor ® S30670 S50670 S70670 User’s Guide...
Page 2: Copyrights And Trademarks
EPSON printer. Epson is not responsible for any use of this information as applied to other printers. Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the U.S.)
Page 3: Table Of Contents
Starting EPSON LFP Remote Panel 2........
Page 4 Chapter 2 Basic Operations Loading and Exchanging Media ..........39 Loading Media - S70670/S50670 .
Page 5 Chapter 4 Using the Control Panel Menu Menu Operations ............147 Menu List .
Page 6 Contacting Epson Support........
Page 7: Important Safety Instructions
Chapter 1 Introduction Important Safety Instructions Read all of these instructions before using the printer. Also be sure to follow all warnings and instructions marked on the printer. When choosing a place for this product ❏ Place this product on a flat, stable surface that is larger than this product. This product will not operate properly if it is tilted or at an angle.
Page 8: When Using This Product
❏ The printer requires two power cables with a combined capacity of 20 A at 100 V or 10 A at 240 V. If the combined capacity can not be supplied by a single outlet, connect the cables to different outlets with independent power sources. ❏...
Page 9: Warnings, Cautions, Important And Notes
❏ If you remove an ink cartridge for later use, protect the ink supply area from dirt and dust, and store it in the same environment as this product. Note that there is a valve in the ink supply port, making covers or plugs unnecessary, but care is needed to prevent the ink from staining items that the cartridge touches.
Page 10: Printer Parts
Printer Parts Front section - S50670 and S70670 Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. See “Cleaning Around the Print Head” on page 126. Additional print drying system The additional print drying system can be used to rapidly dry ink after printing.
Page 11 Roll core holder locking screw The locking screws keep the roll core holders in place once they have been attached to the roll core. There are two lift levers: one on the left and one on the right. Roll support Place the used roll core for media take-up on these holders.
Page 12 USB port Connects the USB cable. Maintenance cover (right) Open this cover when performing regular maintenance. Normally closed when using the printer. See “Regular Maintenance” on page 121. Media loading lever After loading media, lower the media loading lever to keep the media in place. Raise the lever to release the media prior to removal.
Page 13: Front Section - S30670
Front section - S30670 1 Maintenance cover (left) Open this cover to clean the area around the print head. Normally closed when using the printer. See “Cleaning Around the Print Head” on page 126. 2 After heater The heater can be used to rapidly dry ink after printing. See “Heating &...
Page 14 8 Manual switch Use this switch to select the manual take-up direction. The selected option takes effect when the Auto switch is in the Off position. 9 Casters There are two casters on each leg. Once installation is complete, the front casters should be kept locked while the printer is in use.
Page 15: Inside - S70670, S50670
On/flashing : An error has occurred; the type of error is indicated by how the lamp lights or flashes. Check the message on the control panel’s screen. : No error. 24 Control panel See “Control panel” on page 20. 25 Front cover Open when loading media, cleaning the inside of the printer, or removing jammed media.
Page 16 Pressure rollers (high) There are ten rollers in total; the high pressure rollers are the two on the outside edges. They press down on the edges of the media during ink layering. See “Cleaning the Platen Heater, Pressure Rollers, and Media Holding Plates” on page 112. See “High Print Quality”...
Page 17: Inside - S30670
Inside - S30670 Dirt on any of the following parts may reduce print quality. Regularly clean or exchange these parts as described in the chapters listed in the reference sections below. 1 Print head The print head prints by moving left and right while emitting ink. We recommend that you clean the area around this unit once a week.
Page 18: Back
These screws fix the roll holders in place once the media has been installed. There are two screws: one on the left and one on the right. 4 EPSON LiftAssist lever If the media to be mounted on the roll holders seems heavy, use these levers to raise the media effortlessly to the level of the roll holders.
Page 19: Lan Port
5 Pre-heater Heats the media before printing so that the print area is not subject to sudden changes in temperature. 6 Roll support Rest media on these supports before placing it on the roll holders. There are two supports: one on the left and one on the right. 7 Handle After placing media on the right roll holder, rotate the handle to press the holder and apply pressure to the roll core.
Page 20: Control Panel
Control panel 1 P button (power button) Turns the power on and off. 2 P light (power light) The printer's operational status is indicated by a lit or flashing light. The power is on. Flashing The printer is receiving data or performing head cleaning or other operations during shut-down. The power is off.
Page 21 4 Display Displays the printer's status, menus, error messages, and so on. See “Understanding the Display” on page 22. 5 Menu button Press this button to display menus. See “Using the Control Panel Menu” on page 147. 6 y button (back button) Press this button to exit to the previous menu when options are displayed.
Page 22: Understanding The Display
12 W button (pause/cancel button) The printer enters pause status if this is pressed while printing. To release the pause status, press the W button again, or select Pause Cancel on the screen and then press the Z button. To cancel print jobs being processed, select Job Cancel on the screen and then press the Z button.
Page 23 3 Media info From left to right, this display shows the selected media, platen gap, media width, and media remaining. If a media setting bank number created with this printer is selected as the print media, the number (from 1 to 30) will be displayed.
Page 24 Note: You can also check the level of ink remaining using the Ink Level option in the menus. See “The Ink Level Menu” on page 160. 2 Ink color codes : Black : Yellow : Magenta : Cyan Metallic Silver Light Black Orange Light Cyan...
Page 25 6 Head strike detection status This is displayed by the S50670 only. The printer checks whether the media lifts during printing. The printer does not check whether the media lifts during printing. See the “The Maintenance Menu” on page 159. 7 Additional print drying system status (system included with the S50670 and optional for other models) This display shows settings for the optional additional print drying system.
Page 26: Features
The printer uses high-capacity, 700 ml ink cartridges (white cartridges 600 ml, metallic silver cartridges 350 ml) to ensure productivity, reducing the nuisance of frequent ink replacements. High-Speed Printing ® The S-Series printers all use the EPSON MicroPiezo TFT print head(s) for extreme print speeds. Introduction...
Page 27: High Print Quality
Additional Print Drying System Available The additional print drying system (included with the S50670; optional with other models) can be used for increased drying performance and improved productivity. It is recommended when using the S70670 in 10 color mode, as the white and metallic silver inks are slow to dry.
Page 28 In addition to roll supports that give you a place to rest media during installation, the printer offers lift levers that allow heavy media to be effortlessly raised to the level of the roll holders. Virtually Odorless Solvent Ink The distinctive odor of solvent-based inks has been reduced with our solvent inks. This not only improves the work environment during printing but ensures that items intended for indoor display can be exhibited in any venue.
Page 29: Notes On Usage And Storage
Notes on Usage and Storage Installation space Make sure that you secure the following space, clear of any other objects, so that paper ejection and consumable replacement are not obstructed. For the external dimensions of the printer, see “Specifications Table” on page 180. 100 mm (3.9 in.) 1750 mm 500 mm (19.7 in.)
Page 30 ❏ Do not bend or tug the waste ink tube. Ink could spill inside or around the printer. ❏ The following components require regular maintenance at recommended intervals or according to the frequency with which the printer is used. Failure to perform regular maintenance could result in loss of print quality.
Page 31: Notes When Not Using The Printer
Notes when not using the printer If you are not using it, note the following points when storing the printer. If it is not stored correctly, you may not be able to print properly the next time it is used. Additional precautions are required for white and metallic silver inks.
Page 32: Notes On Handling Ink Cartridges
Whether head washing is required depends on the length of time the printer will be left unused. ❏ S70670 (8 color mode): 2 weeks or more ❏ S50670 (4 color mode): 3 weeks or more ❏ S30670: 1 month or more See the “The Maintenance Menu”...
Page 33: Handling Media
❏ Use a cleaning stick from the supplied maintenance kit to wipe ink from the ink supply port of cartridges that have been removed from the printer before all the ink is used. Dried ink on the supply port may cause ink leaks when the cartridge is reinserted and used.
Page 34 Notes on Handling ❏ Do not fold the media or damage the printable surface. ❏ Do not touch the printable surface. Moisture and oils from your hands can affect print quality. ❏ When handling media, hold it by both edges. We recommend wearing cotton gloves. ❏...
Page 35: Specialty Inks
Specialty Inks The term “specialty inks” is used for white and metallic silver inks. White and metallic silver inks are prone to settling (components settling to the bottom of the liquid). Using the ink in this state can cause a decline in print quality and printer malfunction. This section describes precautions for handling white and metallic silver inks.
Page 36: Using The Supplied Software
EPSON LFP Remote Panel 2 is used to update firmware from a computer and copy the media settings bank created in the printer’s setup menu to a computer. See “Starting EPSON LFP Remote Panel 2” on page 36 and “Exiting EPSON LFP Remote Panel 2” on page 37.
Page 37: Exiting Epson Lfp Remote Panel 2
2. Click the desired item in the EPSON LFP Remote Panel 2 main window. See EPSON LFP Remote Panel 2 help for more information. Exiting EPSON LFP Remote Panel 2 Click Finish in the EPSON LFP Remote Panel 2 main window.
Page 38 4. Select the target printer icon, and then click OK. 5. Follow the on-screen instructions to continue. When the delete confirmation message appears, click Yes. If you are reinstalling the EPSON communications driver, restart the computer. Introduction...
Page 39: Chapter 2 Basic Operations
Chapter 2 Basic Operations Loading and Exchanging Media The process for loading media varies with the model of printer or type of media feeding unit used. Choose the method suited to your particular setup. Caution: ❏ The heaters and media holding plates may be hot; observe all necessary precautions. Failure to observe the necessary precautions could result in burns.
Page 40 When the Standard Media Feeding Unit Is Installed This section uses the S70670 to illustrate the process of loading media when the supplied media feeding unit is installed. Caution: Because the media is heavy, it should not be carried by one person. When loading or removing the media, use at least two persons.
Page 41 Printable side out Printable side in Note: Be sure the option selected for Roll Type in the Customize Settings menu matches how the media is rolled. Roll Type defaults to Printable Side Out. Be sure to select Printable Side In after loading media rolled printable side in. For more information see “Roll Type” on page 98.
Page 42 Note: If the label with black squares is not in place, affix the label as described in the Setup Guide. 5. Raise the lift lever on the left side of the printer to lift the media into position, then firmly insert the roll holder.
Page 43 If the roll of media has the outer diameter which is less than 140mm (5.5 inches), lift it up by your hands, and set it to the roll holder as described in Step 5. 8. Tighten the roll holder screw to fix the roll holder in place. Basic Operations...
Page 44 9. Rotate the handle until part A in the illustration below is fully inserted. Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. 10. Raise the media loading lever. Basic Operations...
Page 45 11. Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In 12. Insert the media past the pressure rollers and lower the media loading lever to hold it in place.
Page 46 14. Hold the center of the media and raise the media loading lever. 15. Pull the media straight forward until the edge is past the label on the left side of the after heater. Keep the right edge of the media parallel with the scale markings on the two labels on the right side of the after heater.
Page 47 Position the low pressure rollers 5 mm (0.20 inch) and the high pressure rollers 10 mm (0.39 inch) from the edges of the media, keeping them in the bounds shown by the black labels (see “Printable area - S70670/S50670” on page 107, “Printable Area - S30670”...
Page 48 Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the media slightly. Be sure, however, to stop rewinding before the leading edge of the media is over the cutter groove (on the pressure roller side).
Page 49 Important: ❏ Do not use the media holding plates with media that is more than 0.4 mm (0.02 inch) thick. The media holding plates could touch and damage the print head. ❏ Move the media holding plates to the left and right edges of the platen when they are not in use.
Page 50 Important: When white and metallic silver inks are installed, maintenance will be performed automatically to prevent ink accumulating in the printer and causing clogs. Because turning the printer off prevents maintenance being performed, leading to printer malfunction, we recommend that the printer not be turned off. 2.
Page 51 Printable side in Note: Be sure the option selected for Roll Type in the Customize Settings menu matches how the media is rolled. Roll Type defaults to Printable Side Out. Be sure to select Printable Side In after loading media rolled printable side in. For more information, see “Roll Type”...
Page 52 5. Align the media and the roll holders. Raise or lower the lifter until the media roll core is level with the roll holders. 6. Fully insert the left roll holder. Next, tighten the roll holder screw to fix the roll holder in place.
Page 53 8. Remove the lifter. 9. Rotate the handle until part A in the illustration below is fully inserted. Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is not hidden even after turning the handle until it can no longer be turned, return to step 7 and fully press the right unit into the roll core.
Page 54 11. Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable Side Out Printable Side In 12. Insert the media past the pressure rollers and lower the media loading lever to hold it in place.
Page 55 14. Hold the center of the media and raise the media loading lever. 15. Pull the media straight forward until the edge has past the label on the left side of the after heater. Keep the right edge of the media parallel with the scale markings on the two labels on the right side of the after heater.
Page 56 Position the low pressure rollers 5 mm (0.20 inch) and the high pressure rollers 10 mm (0.39 inch) from the edges of the media, keeping them in the bounds shown by the black labels (see “Printable area - S70670/S50670” on page 107, “Printable Area - S30670”...
Page 57 Note: If you would prefer to print from the very start of the roll, press the u button in the control panel to rewind the media slightly. Be sure, however, to stop rewinding before the leading edge of the media is over the cutter groove (on the pressure roller side).
Page 58: Loading Media - S30670
Important: ❏ Do not use the media holding plates with media that is more than 0.4 mm (0.02 inch) thick. The media holding plates could touch and damage the print head. ❏ Move the media holding plates to the left and right edges of the platen when they are not in use.
Page 59 Center the roll supports between the roll holders. Important: If the right holder handle shaft is not visible, rotate the holder forward until it stops. The media can not be properly loaded if the handle shaft is not visible. 3. Place media on the roll support oriented according to how it is rolled (see below) and position it as indicated by the mark on the label.
Page 60 Printable side in If the label does not have the loading position, mark it on the label as instructed in the Setup Guide. Note: Be sure the option selected for Roll Type in the Customize Settings menu matches how the media is rolled. Roll Type defaults to Printable Side Out. Be sure to select Printable Side In after loading media rolled printable side in.
Page 61 If the roll of media has an outer diameter which is less than 140 mm (5.5 inches), lift it up by your hands, and place it on the roll holder. The roll core will not reach the holder when raised using the lift lever. 5.
Page 62 If the roll of media has an outer diameter which is less than 140 mm (5.5 inches), lift it up by your hands, and place it on the roll holder as described in Step 4. 7. Tighten the roll holder screw to fix the roll holder in place. Basic Operations...
Page 63 8. Rotate the handle until part A in the illustration below is fully inserted. Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. 9. Raise the media loading lever. Basic Operations...
Page 64 10. Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable side out Printable side in 11. Insert the media past the pressure rollers and lower the media loading lever to hold it in place.
Page 65 Important: Perform Steps 11 to 3 in reverse order and repeat the loading process if the left edge of the media is not within the guides. Do not attempt to reposition the roll holders while they are inserted in the media. 12.
Page 66 Keep the right edge of the media parallel to the scale markings on the two labels on the right side of the after heater. 15. Lower the media loading lever to hold the media in place. To print immediately, proceed to Step 16. For information on loading the media into the auto take-up reel unit, see “Using the Auto Take-up Reel Unit”...
Page 67 First, position the plates so that the edges of the media are in the centers of the round holes. Next, adjust the position so that the white line is visible in the square window and push the plates down to lock them in place and keep them from lifting. Important: ❏...
Page 68 17. Close the front cover. Using the Optional Heavy Roll Media Feeding Unit This section describes how to load media when the optional heavy roll media feeding unit is installed. We recommend using a lifter for media over 40 kg (88.2 lb). The explanation that follows assumes that a lifter is used.
Page 69 1. Turn on the printer by pressing the P button. 2. Loosen the roll holder fixing screws and adjust the roll holders so that the gap between the two is wider than the media. Important: If the right holder handle shaft is not visible, rotate the holder forward until it stops. The media can not be properly loaded if the handle shaft is not visible.
Page 70 Printable side in If the label does not have the loading position, mark it on the label as instructed in the Setup Guide supplied with the optional heavy roll media system. Note: Be sure the option selected for Roll Type in the Customize Settings menu matches how the media is rolled.
Page 71 Raise or lower the lifter until the media roll core is level with the roll holders. 5. Fully insert the left roll holder. Next, tighten the roll holder screw to fix the roll holder in place. 6. Fully insert the right roll holder. Next, tighten the roll holder screw to fix the roll holder in place.
Page 72 8. Rotate the handle until part A in the illustration below is fully inserted. Important: Once part A is hidden, do not turn the handle any further. Failure to observe this precaution could damage the roll holder. If part A is not hidden even after turning the handle until it can no longer be turned, return to step 6 and fully press the right unit into the roll core.
Page 73 10. Pull out the media and insert it into the printer. Note: Media that is heavy and difficult to unroll can be fed by pressing the drive switch on the left roll holder. Printable side out Printable side in 11. Insert the media past the pressure rollers and lower the media loading lever to hold it in place.
Page 74 Important: Perform Steps 11 to 3 in reverse order and repeat the loading process if the left edge of the media is not within the guides. Do not attempt to reposition the roll holders while they are inserted in the media. 12.
Page 75 Keep the right edge of the media parallel with the scale markings on the two labels on the right side of the after heater. 15. Lower the media loading lever to hold the media in place. To print immediately, proceed to Step 16. For information on loading the media into the auto take-up reel unit, see “Using the Auto Take-up Reel Unit”...
Page 76 First, position the plates so that the edges of the media are in the centers of the round holes. Next, adjust the position until the white line is visible in the square window and push the plates down to lock them in place and keep them from lifting. Important: ❏...
Page 77: Viewing And Changing Media Settings
17. Close the front cover. Viewing and Changing Media Settings The control panel displays the following information once the media lever is lowered. This display can be used to view or change the following two options: ❏ Remaining Setup On: The printer displays the amount of media remaining. Off: The printer does not display the amount of media remaining.
Page 78 XXXXXXXXXXXXXXXXXX: Media settings are based on those stored in the printer in media settings bank No. 1. Media settings banks can store a variety of settings for different media based on the options selected in the Heater Temperature, Media Suction, Head Alignment, and other menus.
Page 79: Exchanging Media
The printer will display Ready after a brief pause, showing that it is ready to print. Transmit the data to be printed from the computer. Exchanging Media To replace the media after printing, print the amount of media remaining, cut the media, and remove the roll.
Page 80 2. Press the M button, select Media Remaining in the menu, and press the Z button. 3. Select Print Remaining Length and press the Z button. 4. Press the Z button to print the amount of media remaining. Cutting Media Use a cutter (not included) to cut the media when printing is complete.
Page 81 If you have printed the amount of media remaining, press the u button to rewind the media so that this information will remain on the roll after the media is cut. 3. Remove the media holding plates. 4. Cut the media with the cutter. Pass the blade of the cutter down the cutting groove.
Page 82: Using The Auto Take-Up Reel Unit
Note: If you are using the auto take-up reel unit, set the Auto switch on the auto take-up reel unit to Off before using the Manual switch to position the media over the cutting groove. If you are using the S70670 or S50670 and do not intend to make additional prints, raise the media loading lever to prevent deformation of the pressure rollers.
Page 83 Caution: Be sure that your hands or hair do not get caught in the auto take-up reel unit while it is in operation. Failure to observe this precaution could result in injury. Follow the instructions in the manual when loading media or roll cores or removing media from the take-up roll.
Page 84 Center the roll supports between the roll holders. 3. Align the right roll core holder with the right edge of the media and tighten the fixing screw. 4. Insert the roll core onto the right holder. 5. Insert the left holder into the roll core. Basic Operations...
Page 85 Slide the holder in until part A in the illustration below is fully inserted. Important: Stop when part A is no longer visible. The take-up reel unit may not function as expected if the holder is inserted too far. 6. Tighten the roll core holder fixing screw to fix the roll core holder in place. See the following for further instructions.
Page 86 Counterclockwise Take Up 1. Attach the media to the take up roll core. Tape the media to the take up roll core in the center and then at the left and right edges. 2. Press the d button in the control panel to feed enough media for a single wrap around the roll core.
Page 87 4. Flip the Auto switch to 5. Lower the tension bar. 6. Press the d button to feed the media until the take up roll core begins to turn. Important: The auto take-up reel unit will not work if the tension bar is raised. Basic Operations...
Page 88 Clockwise Take Up 1. Attach the media to the take up roll core. Tape the media to the take up roll core in the center and then at the left and right edges. 2. Press the d button in the control panel to feed enough media for a single wrap around the roll core.
Page 89 4. Flip the Auto switch to 5. Lower the tension bar. 6. Press the d button to feed the media until the take up roll core begins to turn. Important: The auto take-up reel unit will not work if the tension bar is raised. Basic Operations...
Page 90: Removing The Take-Up Roll
Removing the Take-up Roll The procedure for removing media varies depending on whether you are using the installed auto take-up reel unit or the optional auto take-up reel unit for heavy media. Follow the steps below when using the supplied auto take-up reel unit. Caution: Because the media is heavy, it should not be carried by one person.
Page 91: Before Printing
6. Loosen the right roll core holder fixing screw and remove the roll core holder from the roll. 7. Lower the roll onto the roll support. Before Printing To maintain print quality, perform the following inspection before starting work each day. ❏...
Page 92: Saving Optimal Settings For The Current Media (Print Media Settings)
White and metallic silver inks must be removed and shaken once every 24 hours. Although a message is displayed in the control panel 24 hours after the inks were last removed, we recommend that they be removed and shaken before the start of work. See “How to replace”...
Page 93: Saving Settings
❏ Head Movement ❏ Multi-Strike Printing ❏ Roll Type ❏ Tension Measurement ❏ Media Tension ❏ Feed Speed For more information on these items, see “The Media Setup Menu” on page 152. Saving Settings Follow the steps below to save media settings. Choosing a Media Setting Bank 1.
Page 94 Note that any settings already saved to the printer will be overwritten. Setting Name Name the media setting bank. Using distinctive names makes it easier to select banks for use. 1. Select Setting Name and press the Z button. 2. Use the d/u buttons to display letters and symbols. When the desired character is displayed, press the r button to select the next entry position.
Page 95: Platen Gap
Note: Feed Adjustment varies with the media used. Load the media for which feed adjustment is required under the same conditions as the actual print job. For example, if you are using the auto take-up reel unit for printing, the auto take-up reel unit should also be used for feed adjustment. Furthermore the media must be loaded and feed adjustment performed again after the heavy roll media system is installed even if feed adjustment has already been performed using standard roll media system.
Page 96: Head Alignment
Head Alignment Select Head Alignment to correct print head mis-alignment when print results seem grainy or out of focus. The Head Alignment menu contains two options: Auto and Manual. Auto head alignment aligns the head automatically using data collected by a sensor while a test pattern is printed.
Page 97 Heating & Drying Set the temperature of the heaters or turn the fan for the additional print drying system on or off (included with the S50670 and optional with other models). Note: Adjust heater temperature as follows: ❏ Set the heaters to the temperatures recommended in the documentation provided with the media, if available.
Page 98 Head Movement Choose the range in which the print head moves during printing. 1. Use the d/u buttons to select Head Movement and press the Z button. 2. Use the d/u buttons to select the desired setting and press the Z button. For faster printing, select Data Width.
Page 99: Changing Heater And Fan Settings
Media Tension Increase tension if creases appear in the media during printing. The higher the value, the greater the tension. If you have previously performed Feed Adjustment, you will need to perform it again after adjusting Media Tension. See “Feed Adjustment” on page 94. 1.
Page 100 Platen heater: 40 °C (104 °F) After heater: 50 °C (122 °F) Heater status can be viewed in the control panel. See “Understanding the Display” on page Additional Dryer defaults to On; at this setting, the fan turns on automatically when printing starts.
Page 101: Correcting Print Misalignment (Head Alignment)
Additional Dryer (1) Use the d/u buttons to select On or Off. (2) Press the Z button. Correcting Print Misalignment (Head Alignment) Given that there is a slight gap between the print head and the media, the landing sites for the different colors of ink may be affected by humidity, temperature, inertial forces imparted by the print head, or the direction of the print head as it moves from right to left or left to right, or the use of two print heads (all models except S30670).
Page 102 4. Use the d/u buttons to select a media setting bank number between 1 and 30 and then press the Z button. Note that any settings already saved in the printer will be overwritten. 5. Use the d/u buttons to select Head Alignment and press the Z button. 6.
Page 103: Feed Adjustment (Manual Feed Adjustment)
Feed Adjustment (Manual Feed Adjustment) Feed Adjustment is used to correct banding (horizontal banding, lines, or strips of uneven color). Feed Adjustment can be performed automatically or manually. For more information on automatic feed adjustment, see “Feed Adjustment” on page 94. This section explains how to perform manual feed adjustment.
Page 104: Using A Test Pattern
Using a Test Pattern Primary and Secondary adjustments are required. Normally the Secondary adjustment is performed after the Primary adjustment. Primary adjustment alone may be sufficient if you only wish to accurately print the length of a design. 1. After confirming that the printer is ready to print, press the Menu button. The settings menu will be displayed.
Page 105 When printing is complete, the media will automatically be fed to a position where the pattern is clearly visible. 10. Measure the distance between the “+” symbols. Record either the distance between the two center symbols or the average of the distances between the left, center, and right symbols.
Page 106: Performing Feed Adjustment During Printing
In the following example, this would be pattern number 3. 16. The pattern number is displayed in the control panel. Using the d/u buttons, enter the pattern number recorded in Step 15 and press the Z button. 17. Enter the number for each line, from A to F, and press the Z button. 18.
Page 107: Printable Area - S70670/S50670
If, in contrast, the feed amount is too large, white bands (pale stripes) will appear; adjust the feed amount downwards. 3. If you are not satisfied with the results, use the d/u buttons to enter an adjustment value. 4. Press the Z button when settings are complete. Once the feed amount has been adjusted, printing will continue at the new value.
Page 108: Using The High Pressure Rollers
* Ink layering not available with media of this width. See “High Print Quality” on page 27. Note: Pressure rollers not within the bounds indicated by the black labels do not apply pressure to the media when the media loading lever is lowered. Pressure rollers that are within a black label but not over the media will cause friction during printing;...
Page 109: Using The Low Pressure Rollers
508–1626 mm (20–64 in.) 5 mm (0.2 in.) 10 mm (0.4 in.) 10 mm (0.4 in.) 3–25 mm 3–825 mm (0.1–1 in.) (0.1–32.5 in.) 10 mm 10 mm (0.4 in.) (0.4 in.) 5 mm (0.2 in.) A: Pressure rollers (high) *1 The value selected for Side Margin(Left) in the setup menu.
Page 110: Printable Area - S30670
300–1626 mm 3–825 mm 3–25 mm (11.8–64 in.) (0.1–32.5 in.) (0.1–1 in.) 5 mm 5 mm 5 mm (0.2 in.) (0.2 in.) (0.2 in.) 5 mm (0.2 in.) A: Pressure rollers (low) *1 The value selected for Side Margin(Left) in the setup menu. The default value is 5 mm (0.2 inch). Choose a Side Margin(Left) over 10 mm (0.4 inch) when using media holding plates.
Page 111 1 (right edge of media) Varies with the option selected for Media Size Check. On selected for Media Size Check: The right edge of the media. Off selected for Media Size Check: The default right edge position (as far as the platen past the center of the label on the pre-heater).
Page 112: Chapter 3 Maintenance
Chapter 3 Maintenance Daily Maintenance To maintain print quality, perform the following inspection and cleaning before starting work each day. Cleaning the Platen Heater, Pressure Rollers, and Media Holding Plates Caution: ❏ The heaters and media holding plate may be hot; observe all necessary precautions. Failure to observe the necessary precautions could result in burns.
Page 113 S70670, S50670: S30670: 5. Clean the media holding plates and platen heater. Maintenance...
Page 114: Checking For Clogged Nozzles
Dampen a soft cloth in water, wring it out thoroughly, and use it to remove lint and dust from the media holding plates on both the left and right sides and from the platen. Checking for clogged nozzles We recommend that you check the nozzles for clogs each time you print to ensure quality results.
Page 115 Note: Auto Nozzle Check is not available under the following conditions: ❏ White ink is used in10 color mode (S70670) or 5 color mode (S50670). The check can still be performed with other colors. ❏ The media is transparent or colored. ❏...
Page 116 This section explains how to print and inspect a check pattern. 1. After confirming that the printer is ready, press the # button. The Maintenance menu will be displayed. 2. Select Nozzle Check and press the Z button. 3. A nozzle pattern will be printed. When printing is complete, the media will automatically be fed to a position where the pattern is clearly visible.
Page 117: Maintenance Procedures For Specialty Inks
Example of clogged nozzles Perform head cleaning if any segments are missing from the pattern. See “Head Cleaning” on page 119. 5. The menus close when printing is complete. Head Mode Adjustment The S70670 and S50670 each have two print heads, meaning that if either clogs, printing can continue using the other.
Page 118 ❏ Once every 24 hours, agitate the white and metallic silver ink cartridges. This prevents settling inside the cartridge. See “How to replace” on page 143. ❏ When white and metallic silver inks are installed, maintenance will be performed automatically to prevent ink accumulating in the printer and causing clogs. Because turning the printer off prevents maintenance being performed, leading to printer malfunction, we recommend that the printer not be turned off.
Page 119: Head Cleaning
2. Using the d/u buttons, highlight Ink Circulation, WH,MS Ink Refresh, or WH,WH Ink Refresh and press Z. The printer will circulate or refresh the ink. Head Washing S70670 If the printer is to be stored for more than 1 week and powered off, it is recommended to perform a head washing on all colors.
Page 120 Note: If colors are faint or missing even after head cleaning, perform regular part cleaning. See “Regular Part Cleaning” on page 124. Auto Maintenance Options The printer features handy auto maintenance options for performing regular head cleaning at an interval selected as described below. ❏...
Page 121: Regular Maintenance
3. Choose the nozzles to be cleaned. All Nozzles Choose this option if all patterns in the printed nozzle check results contain faint or missing segments. If you select All Nozzles, proceed to Step 5. Selected Nozzles Choose this option if only some of the numbered patterns (nozzle arrays) in the printed nozzle check results contained faint or missing segments.
Page 122: Regular Part Cleaning: Preparation And Notes
Regular Part Cleaning: Preparation and Notes What You’ll Need Ready the following items before beginning regular part cleaning. ❏ Protective eyeware (not included) Protects your eyes from ink and ink cleaner. ❏ A maintenance kit (supplied with printer) Contains gloves, cleaning sticks, wiper, wiper cleaner, and flushing pad. Order new maintenance kits once the contents of the supplied maintenance kit are exhausted.
Page 123 Failure to observe this precaution could result in malfunction or reduced print quality. ❏ Use only the supplied cleaning sticks or sticks contained in maintenance kit (consumable kits, available separately). Other types of stick that produce lint will damage the print head. ❏...
Page 124: Regular Part Cleaning
1. Pour about 10 ml of ink cleaner into the cup supplied with the ink cleaner. 2. Dampen the cleaning stick with ink cleaner. Do not allow ink cleaner to drip from the cleaning stick. 3. Wipe the spot you wish to clean. Important: ❏...
Page 125 Clean the parts in the following order: (1) Print head (2) Wiper (3) Caps (4) Wiper rail Moving the Print Head This section describes how to position the print head for part cleaning. Important: Be sure to follow the steps below when positioning the print head. Moving the print head manually could cause malfunction.
Page 126: Cleaning Around The Print Head
4. Open the maintenance covers at each end. Cleaning Around the Print Head Inspect the area around the print head and remove any ink stains as described below. Note that the S70670 and S50670 have two print heads; be sure to inspect both. 1.
Page 127 S70670/S50670 The print head on the left is Head 1, and the print head on the right is Head 2. S30670 Maintenance...
Page 128 Important: ❏ Be sure not to touch the nozzle surface during cleaning. Failure to observe this precaution could damage the print head. ❏ The parts shown below are sensors. Be careful not to touch this area with your hands or clean room wipes. Failure to observe this precaution could affect print quality. Cleaning Wiper and Caps The S70670 and S50670 have two wipers and ten caps.
Page 129 2. Remove the wiper. Holding the wiper by the attachment point, tilt it to the left and lift it out. 3. Clean the front and back of the wiper with a cleaning stick. 4. Clean the bottom of the wiper with a cleaning stick. Maintenance...
Page 130 5. Clean the attachment points with a cleaning stick. 6. Return the wiper when cleaning is complete. Place the wiper on the attachment point and press it down until it clicks into place. If the remaining wiper for the S70670 or S50670 is stained, repeat the process from Step 1.
Page 131: Cleaning The Wiper Rail
Important: Do not touch the insides of the caps. Failure to observe this precaution could deform the affected parts. Cleaning the Wiper Rail Important: Failure to regularly clean the wiper rail could result in product malfunction. 1. Press the Z button to move the wiper to the rear. 2.
Page 132 3. Dampen a cleaning stick with ink cleaner (available separately). See “Using Ink Cleaner” on page 123 4. Clean the area shown. 5. Return the wiper cleaner that was removed in Step 2 to its original position. Place it on the attachment point and press down until you hear a click. Users of the S70670 or S50670 will need to return to Step 2 and clean the remaining rail.
Page 133: Disposing Of Waste Ink
Consign disposal of waste inks to an industrial waste disposer. At this point, please provide the Waste Ink Data Sheet to the industrial waste disposer. You can download it from the EPSON website. The printer tracks waste ink and displays a message when the counter reaches the warning level.
Page 134: Replacing The Waste Ink Bottle
Important: Only reset the counter when replacing the waste ink bottle. Resetting the counter before the waste ink bottle is replaced will result in the printer being unable to accurately track the waste ink level. Replacing the Waste Ink Bottle 1.
Page 135: Replacing The Wiper And Wiper Cleaner
Important: ❏ Be sure to confirm that the waste ink tube is inserted in the mouth of the waste ink bottle. Ink will spill onto the surrounding area if the tube is not inserted in the bottle. ❏ You will need the lid for the waste ink bottle when disposing of waste ink. Keep the lid in a safe place;...
Page 136 4. Open the right maintenance cover. 5. Remove the wiper cleaner. Grasp the cleaner as shown and lift it from the printer. 6. Insert a new wiper cleaner. Maintenance...
Page 137 Place it on the attachment point and press down until you hear a click. 7. Remove the wiper. Holding the wiper by the attachment point, tilt it left and lift it out. 8. Insert the new wiper. Maintenance...
Page 138: Replacing The Flushing Pad
Place it on the attachment point and press down until you hear a click. Users of the S70670 or S50670 will need to return to Step 5 and replace the remaining wiper. 9. Close the maintenance cover and press the Z button. The menus will close when the print head returns to its normal position.
Page 139 1. Confirm that the printer is on and press #. The Maintenance menu will be displayed. 2. Use the d/u buttons to select Head Maintenance and press the Z button. 3. Press the Z button to move the print head to the cleaning position. 4.
Page 140 Insert the two hooks on the flushing pad into the slots as shown and press the tab down until the pad clicks into place. 7. Close the maintenance cover and press the Z button. 8. The menus will close when the print head returns to its normal position. Maintenance...
Page 141: Cleaning Check Sheet
Cleaning Check Sheet Print these pages to track maintenance tasks. Component to be Cleaned on date Explanation cleaned 1 Platen heater, Clean if you notice lint from print media, dust, or ink stains. pressure rollers, media holding plates 2 Print head We recommend that cleaning be performed once a week.
Page 142: Regular Replacement Check Sheet
Regular Replacement Check Sheet Print these pages to track maintenance tasks. Component to be Cleaned on date Explanation replaced 1 Flushing pad We recommend that this component be replaced once every six months. Replace when ink stains appear on the media or when dust or lint from the media appear on the front of the flushing pad.
Page 143: Replacing Ink Cartridges
You can use the same procedure to replace all ink cartridges. Important: Epson recommends the use of genuine EPSON ink cartridges. Epson cannot guarantee the quality or reliability of non-genuine ink. The use of non-genuine ink may cause damage that is not covered by Epson’s warranties, and under certain circumstances, may cause erratic printer...
Page 144 3. Insert a finger into the depression on the top of the cartridge and pull the cartridge straight toward you. Important: Removed ink cartridges may have ink around the ink supply port, so be careful not to get any ink on the surrounding area when removing the cartridges. 4.
Page 145: Parts That Are Periodically Replaced
Match the color of the cartridge to the color of the label on the printer. 6. Lower the lock lever to engage the lock. Repeat steps 2 to 6 to replace other ink cartridges. Important: ❏ Fill all slots using ink or replacement cartridges (replacement cartridges are required in 8 and 4 color modes).
Page 146 Print head life varies with operating conditions. Base the decision to replace the print head on the quality of the print results. Contact your dealer or EPSON Support for information on replacing components. Component status can be printed by selecting Print Status Sheet in the setup menu. See “The Printer Status Menu”...
Page 147: Chapter 4 Using The Control Panel Menu
Chapter 4 Using the Control Panel Menu Menu Operations The menus are used as shown below. Menu List The following items and parameters can be set and executed in the Menu. See the reference pages for more details on each item. Items or values marked with a superscript “1”...
Page 148 Menu Item Parameter Media Setup Media Remaining See “The Media Setup Remaining Setup On, Off Menu” on page 152. Length 5.0 to 99.5 m (15 to 300 ft) Remaining Alert 1 to 15 m (4 to 50 ft) Print Remaining Length Print Select Media RIP Settings, 1 to 30 (media setting bank number)
Page 149 Menu Item Parameter Media Suction 0 to 10 Head Movement Data Width, Printer Full Width Multi-Strike Printing Off, 2 to 8 Roll Type Printable Side Out, Printable Side In Tension Measurement Periodically, Every page, Off Media Tension 0 to 40 Feed Speed 1 to 2 Print Media List...
Page 150 Menu Item Parameter Nozzle Check Print Maintenance See “The Maintenance Cleaning Menu” on page 159. All Nozzles Execute (Light), Execute (Medium), Execute (Heavy) Head 1/Head 2 , Head 1 Head 2 Selected Nozzles Execute (Light), Execute (Medium), Execute (Heavy) Ink Circulation Execute WH, XX Ink Refresh Execute...
Page 151 Menu Item Parameter Date And Time MM/DD/YY HH:MM Preference See “The Preference Language Japanese, English, French, Italian, German, Portuguese, Menu” on page 162. Spanish, Dutch, Russian, Korean, Chinese Unit: Length m, ft/in Unit: Temperature °C, F Alert Sound Setting On, Off Alert Lamp Setting On, Off Reset All Settings...
Page 152: Details Of The Menu
Details of the Menu Items or values marked with a superscript “1” apply to the S70670 and S50670, while items marked with a superscript “2” are available with the S50670 only. Items marked with a superscript “3” are not supported on the S70670. The Media Setup Menu The Media Setup menu can be accessed directly by pressing the M button.
Page 153: Customize Settings
Customize Settings Item Parameter Explanation Current Settings Change settings for currently selected media. The options available depend on whether RIP Settings or a media setting bank is selected. More information on the options available can be found below in the entries for RIP Settings and media setting banks 1 to 30.
Page 154 1 to 30 (media setting bank number) Item Parameter Explanation Setting Name Assign the media setting bank a name up to 22 half-size characters long. Using distinctive names makes it easier to select banks for use. Feed Adjustment Auto Use this option if banding (horizontal banding, lines, or strips of uneven color) persists after head cleaning and head alignment have been Manual performed.
Page 155 Item Parameter Explanation Heater Temperature Pre-heater/platen heater: The temperatures for the pre-, platen, and after heaters can each be 30 °C to 50 °C (86 °F to adjusted separately. 122 °F) After heater: 30 °C to 55 °C (86 °F to 131 °F) Drying Time Per Pass 0 to 10sec Select the time the print head pauses to allow drying after each pass.
Page 156: Printer Setup Menu
Item Parameter Explanation Tension Measurement Periodically Choose Periodically or Every page to have the printer automatically monitor and adjust media tension during printing for optimal results, Every page Off to disable automatic tension adjustment. Periodically is recommended in most circumstances. The printer may however be unable to adjust tension appropriately for some media, resulting in excessive slack or other maladjustments that cause printing problems, in which case you should select Off.
Page 157 Item Parameter Explanation Media Size Check Choose whether the printer automatically detects (On), or does not automatically detect (Off), the edges of the media. Try Off if the printer displays a Media Size Error when the media is correctly loaded. Note, however, that the printer may print beyond the edges of the media when Off is selected.
Page 158 Item Parameter Explanation Nozzle Check Cycle Choose the frequency with which the printer performs an Auto Nozzle Check: never (Off) or once every 1 to 10 pages. Auto nozzle checks will 1 to 10 pages not be performed while Off is selected. If 1 to 10 is selected, the printer will automatically checks for clogs at the specified interval by scanning a test pattern with a sensor as it is being printed.
Page 159: The Maintenance Menu
Item Parameter Explanation Heat Off Timer 15 to 240 minutes You can turn off the heaters automatically when no errors are detected and no print jobs are in progress. This option is used to choose the interval before the heaters turn off automatically. The printer will enter sleep mode when the Heat Off Timer expires.
Page 160: The Ink Level Menu
Item Parameter Explanation WH,MS Ink Refresh Select this option should you notice uneven colors (areas of uneven density) once the printer is turned on following a period of disuse. WH,WH Ink Refresh WH,MS Ink Refresh is available when 10 color mode is selected for the S70670, WH,WH Ink Refresh when 5 color mode is selected for the S50670.
Page 161: The Print Logs Menu
The Print Logs Menu These items are used to track consumables. Item Parameter Explanation Print Job Log Sheet Print You can print the job information saved in the printer (up to 10 jobs). The information includes the media and ink used in each job, making it easier to track the use of consumables.
Page 162: The Preference Menu
Item Parameter Explanation Print Status Sheet Print Use Print Status Sheet to print the current network status. Use this information for a complete overview of network settings. Restore Settings Select Yes to restore all items in the Network Setup menu to their default settings.
Page 163: The Reset All Settings Menu
The Reset All Settings Menu Parameter Explanation Select Yes to reset all settings in the Preference menu except Date And Time, Language, Unit: Length, and Unit: Temperature. Using the Control Panel Menu...
Page 164: Chapter 5 Problem Solver
Use EPSON LFP Remote Panel 2 to update the firmware again. Restart the printer. If this message appears on the LCD panel again, contact EPSON Support. Print head is nearing end of The print head requires periodic replacement. The current print head is nearing the end service life.
Page 165 Messages What to do Auto Take-up Reel Unit stopped. Media is not correctly attached to the auto take-up reel unit. Press the W button and select Job Cancel to cancel printing. Flip the Auto switch on the auto take-up reel unit to Off, then flip it back and reattach the media to the auto take-up reel unit.
Page 166: Error Messages
Turn on the printer again multiple times. If the same call for service is displayed on the LCD panel, contact EPSON Support for assistance. Tell them the call for service code is "XXXX".
Page 167: Troubleshooting
Troubleshooting You cannot print (because the printer does not work) The printer does not turn on. Is the power cable plugged into the electrical outlet or the printer? Make sure the power cable is securely plugged into the printer. Is there any problem with the electrical outlet? Make sure your outlet works by connecting the power cable for another electric product.
Page 168: The Printer Sounds Like It Is Printing, But Nothing Prints
Connect the printer directly to the computer using a USB cable, and then try to print. If you can print via USB, there are some problems on the network environment. Ask your system administrator, or refer to the manual for your network system. If you cannot print via USB, see the appropriate section in this User’s Guide. The printer has an error.
Page 169: The Prints Are Not What You Expected
Are you using a genuine EPSON ink cartridge? This printer is developed for use with EPSON ink cartridges. If you use non-EPSON ink cartridges, printouts may be faint, or the color of the printed image may be changed because the remaining ink level is not correctly detected. Be sure to use the correct ink cartridge.
Page 170 Is Ink Low displayed on the control panel's screen? The print quality may decline when the ink is low. We recommend replacing the ink cartridge with a new one. If there is a difference in color after replacing the ink cartridge, try performing head cleaning a few times. The print is not positioned properly on the media.
Page 171: Media
Is the print head scuffing the printed surface? Smear caused by the print head scuffing the media can be prevented by adjusting the Platen Gap to suit the media. It may also be prevented by choosing a high value for Media Tension. See “Platen Gap”...
Page 172: Media Jams
2. Continue pressing the tensioner until the projections on the inside at both ends contact the case. Media Jams Is the media creased or folded? Media with a strong curl or that is folded back on its leading edge or creased may cause jams or other media feed problems. Do not use media affected by these types of problems.
Page 173: Removing Jammed Media
If a message is displayed and the printer will not turn off, unplug both power cables. 3. Remove the media holding plates, if installed. Important: Cease use of the printer if the media holding plates are deformed. Continued use could damage the pressure rollers or print head. Contact EPSON Support. Problem Solver...
Page 174 4. If the print head is over the media, move it away from the jam. Important: Move the print head only after removing the media holding plates. Contact with deformed media holding plates could damage the print head. 5. Raise the media loading lever. 6.
Page 175: Others
Important: If the printer is left off for an extended period, the print head will be left uncapped and dry out, and will not print properly when printing resumes. Turning the printer on automatically caps the print head. Reload the media and resume printing. See “Loading Media - S70670/S50670” on page 39 or “Loading Media - S30670”...
Page 176: Chapter 6 Appendix
The use Cyan T715200 of non-genuine ink may cause damage that is not covered by Epson’s warranties, and under certain circumstances, may cause erratic printer Magenta T715300 behavior. Information about non-genuine ink levels may not be...
Page 177: Supported Media
Product Part number Explanation Waste Ink Bottle T724000 Identical to the waste ink bottle supplied with the printer. Media Holding Plate C12C890891 Identical to the media holding plate supplied with the printer. High Speed Dryer C890751 Uses a fan to blow air over the media and assist drying (included with the S50670).
Page 178: Moving And Transporting The Printer
Moving and Transporting the Printer This section describes how to move and transport the product. Moving the Printer This section assumes that the product is being moved to another location on the same floor without traversing stairs, ramps, or lifts. See below for information on moving the printer between floors or to another building.
Page 179: Transport
3. Perform a nozzle check to check for clogged nozzles. See “Checking for clogged nozzles” on page 114. 4. Perform Head Alignment and check print quality. See “Head Alignment” on page 96. Transport Before transporting the printer, contact EPSON Support. System Requirements Consult the documentation for your software RIP. Appendix...
Page 180: Specifications Table
Specifications Table Printer Specifications Printing method On-demand ink jet Nozzle configuration S70670: 360 nozzles × 2 rows × 10 colors (Metallic Silver, Light Black, Black, Cyan, Magenta, Yellow, Orange, Light Cyan, Light Magenta, White) S50670: 360 nozzles × 2 × 2 rows × 5 colors (White, Black, Cyan, Magenta, Yellow) S30670: 360 nozzles ×...
Page 181 Printer Specifications Temperature Operating: 15 to 35 °C/59 to 95 °F (20 to 32 °C/68 to 90 °F recommended) Storage: -20 to 40°C (-4 to 104 F) (within a month at 40°C or 104 Humidity Operating: 20 to 80% (40 to 60% recommended) (without condensation) Storage: 5 to 85% (without condensation) Dimension Storage (minimum) dimensions: 2620 (W) ×...
Page 182: Standards And Approvals
Standards and Approvals Safety UL 60950-1 CSA C22.2 No.60950-1 Low Voltage Directive 2006/95/EC EN 60950-1 FCC part 15 subpart B Class A CAN/CSA-CEI/IEC CISPR 22 Class A AS/NZS CISPR 22 Class A EMC Directive 2004/108/EC EN 55022 Class A EN 55024 EN 61000-3-2 EN 61000-3-3 Warning:...
Page 183 WARNING The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device.
Page 184: Appendix A Where To Get Help
Purchase Supplies and Accessories You can purchase genuine EPSON ink cartridges, paper, and accessories from an EPSON authorized reseller. To find the nearest reseller, call 800-GO-EPSON (800-463-7766). Or you can purchase online at http://www.epsonstore.com (U.S. sales) or http://www.epson.ca (Canadian sales).
Page 185: Chapter B Software License Terms
Chapter B Software License Terms Open Source Software Licenses Bonjour This printer product includes the open source software programs which apply the Apple Public Source License Version1.2 or its latest version ("Bonjour Programs"). We provide the source code of the Bonjour Programs pursuant to the Apple Public Source License Version1.2 or its latest version until five (5) years after the discontinuation of same model of this printer product.
Page 186 1.3 "Covered Code" means the Original Code, Modifications, the combination of Original Code and any Modifications, and/or any respective portions thereof. 1.4 "Externally Deploy" means: (a) to sublicense, distribute or otherwise make Covered Code available, directly or indirectly, to anyone other than You; and/or (b) to use Covered Code, alone or as part of a Larger Work, in any way to provide a service, including but not limited to delivery of content, through electronic communication with a client other than You.
Page 187 (a) You must retain and reproduce in all copies of Original Code the copyright and other proprietary notices and disclaimers of Apple as they appear in the Original Code, and keep intact all notices in the Original Code that refer to this License; and (b) You must include a copy of this License with every copy of Source Code of Covered Code and documentation You distribute or Externally Deploy, and You may not offer or impose any terms on such Source Code that alter or restrict this License or the recipients'...
Page 188 3. Your Grants. In consideration of, and as a condition to, the licenses granted to You under this License, You hereby grant to any person or entity receiving or distributing Covered Code under this License a non-exclusive, royalty-free, perpetual, irrevocable license, under Your Applicable Patent Rights and other intellectual property rights (other than patent) owned or controlled by You, to use, reproduce, display, perform, modify, sublicense, distribute and Externally Deploy Your Modifications of the same scope and...
Page 189 8. NO WARRANTY OR SUPPORT. The Covered Code may contain in whole or in part pre-release, untested, or not fully tested works. The Covered Code may contain errors that could cause failures or loss of data, and may be incomplete or contain inaccuracies. You expressly acknowledge and agree that use of the Covered Code, or any portion thereof, is at Your sole and entire risk.
Page 190 11. Ownership. Subject to the licenses granted under this License, each Contributor retains all rights, title and interest in and to any Modifications made by such Contributor. Apple retains all rights, title and interest in and to the Original Code and any Modifications made by or on behalf of Apple ("Apple Modifications"), and such Apple Modifications will not be automatically subject to this License.
Page 191 13.3 Independent Development. Nothing in this License will impair Apple's right to acquire, license, develop, have others develop for it, market and/or distribute technology or products that perform the same or similar functions as, or otherwise compete with, Modifications, Larger Works, technology or products that You may develop, produce, market or distribute.
Page 192: Other Software Licenses
The Original Code and all software distributed under the License are distributed on an 'AS IS' basis, WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, AND APPLE HEREBY DISCLAIMS ALL SUCH WARRANTIES, INCLUDING WITHOUT LIMITATION, ANY WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, QUIET ENJOYMENT OR NON-INFRINGEMENT.
Page 193 Altered versions--including, but not limited to, ports to new operating systems, existing ports with new graphical interfaces, versions with modified or added functionality, and dynamic, shared, or static library versions not from Info-ZIP--must be plainly marked as such and must not be misrepresented as being the original source or, if binaries, compiled from the original source.

This manual is also suitable for:

Surecolor s50670 Surecolor s70670

Epson SureColor S30670 User Manual

Chapter 1 Introduction

Chapter 2 Basic Operations

Chapter 3 Maintenance

Chapter 4 Using the Control Panel Menu

Chapter 5 Problem Solver

Chapter 6 Appendix

Appendix A Where to Get Help

Chapter B Software License Terms

Quick Links

Related Manuals for Epson SureColor S30670

Summary of Contents for Epson SureColor S30670

This manual is also suitable for:

Table of Contents