Advertisement
Quick Links
\
READ AND UNDERSTAND
THESE INSTRUCTIONS
BEFORE INSTALLING FIXTURE
INSTRUCTION
SHEET NO.
'hisfislure
is
intendedfor installation in accordanwwilh the National E lectrical C odeendlocalregulations.
o assurefull compiianc$ with localcadesandregulations, &e&with yourlocalelectrical i nspectorbefore
!stallafion.To preventelectrical s hock,turn off electricity at
fuse box before proceeding,
IS:40712
Retain these instructions for maintenance reference.
1292
Page 1 of 2
INSTRUCTIONS
FOR
INSTALLATION
OF RADIANCE
PENDANT
FIXTURES
FIXTUREASSEMBLYAND INSTALLATION:
1. Carefully remove CENTER STEM ASSEMBLY f rom
packing.
2. Gently pull downward on CANOPY to disengaga from CROSSBAR SPRING CLIPS and axpose CROSSBAR,
3. Mount CROSSBAR and CENTER STEM ASSEMBLY to OUTLET BOX using OUTLET BOX SCREWS (provided with oullet box).
4. Adjust SWIVEL CASTING. For sloped miting appfication$ loosen UPPER LCCK NUT and turn SWIVEL CASTING until "U-SHAPED" opening in
SWIVEL
is parallel
to ceiling plane. This procedure can also be used t reorientation of SWIVEL CASTING is desired on non-sloped ceifings.
NOTE Fixture should only be mounted to mihngs having a maximum slope of 45" or less,
5. Make electrica connections black fixture lead or fixture lead without tracer marks to (hot) black supply lead; white fixture lead or fixture lead with trao?r mark
to (neutral) white supply lead. Uninsulated (bare) fixture wire isagmund and must be connected toa grounding terminal orwirein OUTLET BOX. Use WIRENUTS
(local hardware item). If supply wires are located witfin three inches of ballast, use wire rated for at least 90° C,
6. SldeCANOPY
UPCENTERSTEM ASSEMBLY andallowSWIVELCASTING
topassthrough square opening in CANOPY. Push CANOPY upunti if fully engages
on CROSSBAR SPRING CLIPS and is sealed flush against ceiting,
7. Loosen and remove three BATTERY NUTS and STAR WASHERS from MOUNTING STUDS on LOWER FIXTURE ASSEMBLY,
8. Raise LOWER FIXTURE ASSEMBLY to
MOUNTING
PLATE on CENTER STEM ASSEMBLY and make
electrica connections Snap together BLACK
CONNECTOR from LOWER FIXTURE ASSEMBLY tm
9.
9.
I
<>
9"17-<> 1.1 E m" WRK',!ww%ii%i
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Lightolier RADIANCE PENDANT FIXTURES
Summary of Contents for Lightolier RADIANCE PENDANT FIXTURES
- Page 1 READ AND UNDERSTAND THESE INSTRUCTIONS BEFORE INSTALLING FIXTURE INSTRUCTION SHEET NO. ‘hisfislure intendedfor installation in accordanwwilh the National E lectrical C odeendlocalregulations. IS:40712 o assurefull compiianc$ with localcadesandregulations, &e&with yourlocalelectrical i nspectorbefore !stallafion.To preventelectrical s hock,turn off electricity at fuse box before proceeding, 1292 Page 1 of 2 Retain these instructions for maintenance reference.
- Page 2 WTRlfCTfON SHEET NO. INSTRUCTIONS FOR INSTALLATION OF S:40712 RADIANCE PENDANT FIXTURES CONTINUED Page 2 of 2 JSPENSION CABLE Attachment AND ADJUSTMENT Loosen (do not remove) fhe BATTERY NUTS tha! secure WIREWAY COVERS on each of the three SUPPORT ARMS (Fig. 2 and 3A), 2, Slide each WIREWAY COVER inward towards the renter of the fixiure (Fig, 3A), WIREWAY COVERS (Fig,3B}, 3.
Need help?
Do you have a question about the RADIANCE PENDANT FIXTURES and is the answer not in the manual?
Questions and answers