Table of Contents
Advertisement
Additional Information
Troubleshooting
If you experience any of the following difficulties while using the
system, use this troubleshooting guide to help you remedy the
problem. Should any problem persist, consult your nearest
service center by calling 1-800-898-9020.
No power.
• Is the power cord firmly plugged into the power outlet?
• One of the safety mechanisms may be operating. In this
event, unplug the player from the power outlet briefly and
then plug it in again.
No picture.
• Check that the system is connected securely.
• The video connecting cord is damaged. Replace it with a
new one.
• Make sure you connect the system to the video input
connector on the TV. (see page 14)
• Make sure you turn on the TV.
• Make sure you select the video input on the TV so that you
can view the pictures from this system.
Noise (interference) appears in the picture.
• Clean the disc.
• If video from this system has to go through your VCR to
get to your TV, the copy-protection applied to some DVD
programs could affect picture quality.
The aspect ratio of the screen cannot be changed even
though you set "TV SYSTEM" in the SETUP menu when
you play a wide picture.
• The aspect rate is fixed on your DVD disc.
• Depending on the TV, you may not be able to change the
aspect ratio.
There is no sound or only a very low-level sound is heard.
• The audio connecting cord is damaged. Replace it with a
new one.
• The system is in pause mode or in slow-motion play mode,
or fast forward or fast reverse is performed
• Press PLAY
Severe hum or noise is heard.
• Move your TV away from the audio components.
• The plugs and jacks are dirty. Wipe them with a cloth slightly
moistened with alcohol.
• Clean the disc.
The remote does not function.
• Remove any obstacles between the remote control and
the system.
• Move the remote control closer to the system.
• Point the remote control at the remote sensor on the front
panel.
• Replace all the batteries in the remote control with new
ones if they are weak.
• Check that the batteries are loaded correctly.
2
23
BARBIE BAR330_Eng P13-26.p65
to return to normal play mode.
23
The disc does not play.
• Insert a disc.
• Insert the disc correctly with the playback side facing down
on the disc tray.
• Clean the disc. (see page 12)
• The system cannot play CD-ROMs, etc. (see page 11)
Insert a DVD or a CD disc.
• Check the region code of the DVD disc. (see page 11)
• Moisture has condensed inside the system. Remove the
disc and leave the system turned on for about an hour.
(see page 9)
The system starts playing the DVD automatically.
• The DVD features the auto playback function.
Playback stops automatically.
• Depending on the disc, the auto pause signal is recorded.
While playing such a disc, the system stops playback at the
signal.
Stopping playback, Search, Slow-motion play, repeat play
or Program play, etc., cannot be done.
• Depending on the disc, some of the above operations may
not be available.
Messages do not appear on the TV screen in the language
you want.
• Select the language for OSD in SETUP menu. (see page 20)
The disc must have the language you selected, if not, other
language will be selected.
The language for the sound cannot be changed when you
play a DVD.
• Multilingual sound is not recorded on the DVD.
• Changing the language for the sound is prohibited on the
DVD.
The language for the subtitles cannot be changed when
you play a DVD.
• Multilingual subtitles are not recorded on the DVD.
• Changing the language for the subtitles is prohibited on
the DVD.
The subtitles cannot be turned off when you play a DVD.
• Depending on the DVD, you may not be able to turn the
subtitles off.
The angles cannot be changed when you play a DVD.
• Multi-angles are not recorded on some DVDs.
• Change the angles when the angle marks appears on the
TV screen. (see page 17)
• Changing the angles is prohibited on some DVDs.
The system does not operate properly.
• Static electricity, etc., may affect the system's operation.
Disconnect the AC power cord once, then connect it again.
2/2/2007, 3:30 PM
Advertisement
Table of Contents
