Advertisement
Quick Links
Download this manual
See also:
Installation Manual
One-Way AM Remote R500A
By: Firstech, LLC.
www.compustar.com
USER'S GUIDE
One-Way AM Remote R500A / Alarm Controller CM1000A
FCC ID :O44J1WENR
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesired operation.
CAUTION : Changes or modifications not expressly approved by
the party responsible for compliance could void the
user's authority to operate this device.
By Firstech, LCC
www.compustar.com
Advertisement
Related Manuals for CompuSTAR CM1000A
Summary of Contents for CompuSTAR CM1000A
- Page 1 (2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device. By Firstech, LCC By: Firstech, LLC. www.compustar.com www.compustar.com...
- Page 2 User’s Guide User’s Guide Table of Contents Safety information Page 3 Remote Description: R500A Page 3 Remote Button Functions Page 4 Remote Coding Procedure Page 5 Locking and Unlocking the Doors Page 5 Arming and Disarming System Page 6 Trunk Release Page 6 Panic Mode Page 6...
- Page 3 Servicing your vehicle or loaning it to others When servicing the vehicle, 0.5 sec Lock like changing/checking the oil, or loaning your vehicle to someone who may not be familiar with Compustar systems, it may be best to put the 0.5 sec Unlock system in valet mode.
- Page 4 Remote Coding Procedure Arming and Disarming the System The remote must be coded to the system installed in the vehicle before it To arm the alarm, hold the button down until the LED on the remote stops can be operated in any way. Listed below is the remote coding flashing.
-
Page 5: Ignition Controlled Door Locks
Valet Mode Passive Locking When in Valet mode, locking and unlocking the vehicle doors will be the With Passive Arming/Locking turned on, the system will arm and lock the only operations available through the remote, the system will not arm the doors 30 seconds after closing the last open door. -
Page 6: Anti-Jacking Mode
In a manual transmission vehicle, if the ignition is powered up, the vehicle can be compression or “bump” started without using the starter. Disabling the ignition will keep the vehicle from starting. Installation Guide Anti-Jacking Mode To use Anti-Jacking mode, the starter kill relay must be rewired to an ignition kill, and Anti-Jacking mode must be turned on in the programming Installation Guide Table of Contents options. - Page 7 b. Connecting and insulating wires Installation Tips and Recommendations . Solder all connections. . Insulate all wires with shrink tube or electrical tape. 1. Precautions to prevent locking yourself out c. Make sure that vibration or heat will not damage or otherwise alter your Lower the window in one or more doors before beginning installation.
- Page 8 CON 1 CM1000A Wiring Diagram Red : 12v Constant Input Constant 12-volt (+) positive power input for the control module. This wire must be connected to a constant 12-volt (+) positive source. The proper wire will test 12-volt (+) positive with the key in the off position, while key is in the on position and during crank.
- Page 9 CON 2 Method 2 Positive Trigger Door Lock System (W/O Actuator) < Circuit diagram during unlock output > < Circuit diagram > Method 3 The lock and unlock outputs of the CM1000A External Actuator are actually two pre-wired relays that can be configured in the three following ways listed below.
- Page 10 No.2 Blue : Negative Starter Kill Output Dome Light Dome Light 250mA (-) negative output when armed. This wire will provide a (-) negative output when system is locked and armed, and is pre-wired to the Door Door starter kill relay. Trigger SW Trigger SW (Note:This wire can also be used to trigger after-market L.E.D.
- Page 11 Option Menu No.7 Black/White : Negative Input for Optional Sensor When installing additional sensors, use this wire as the input wire to the alarm module for those sensors. When connecting more than one sensor to any input Features (Optional Setting) wire, you must diode isolate the output wires of each sensor.
-
Page 12: Programming Menu Options
3.Wait a few seconds, and the parking lights will flash the number of times 4. 30 sec Passive Relock corresponding to the option number you are about to modify. If the number of With this option enabled, after disarming the system with the remote, times the lights flash does not correspond with the option you want to change, the system will relock the doors and arm the alarm after 30 seconds if a door wait a few seconds and the siren will sound, signaling that you have...