Hitachi SJ300 Series Replacement Manual page 20

62 Frequency lower limit setting
63 Frequency upper limit setting
64 Jump frequency setting 1
65 Jump frequency setting 2
66 Jump frequency setting 3
67 Jump frequency width setting
68 Allowable instantaneous power failure time
69 Retry wait time before motor restart
Selection of automatic restart mode after
70
instantaneous power failure
71 Voltage trip enable during stop
72 Maximum frequency selection
73 Software lock mode selection
74 STOP key enable
75 Rotational direction restriction
76 Reverse RUN protection enable
77 Analog input selection
78 Analog input active range start frequency
79 Analog input active range end frequency
80 Analog input active range start voltage/current
81 Analog input active range end voltage/current
82 Analog input start frequency enable
83 External frequency filter time constant
84 Frequency arrival signal output method
85 Frequency arrival setting for acceleration
86 Frequency arrival setting for deceleration
87 Over-torque (forward) level setting
88 Over-torque (reverse) level setting
89 Intelligent input terminal 1 function
90 Intelligent input terminal 2 function
91 Intelligent input terminal 3 function
92 Intelligent input terminal 4 function
93 Intelligent input terminal 5 function
94 Intelligent input terminal 6 function
95 Intelligent input terminal 7 function
96 Intelligent input terminal 8 function
No. Name
setting
Digital
Remote Operator
operator
A6 F-26 LIMIT L 0.0Hz
A5 LOMIT H 0.0Hz
A7 JUMP F1 0.0Hz
A8 JUMP F2 0.0Hz
A9 JUMP F3 0.0Hz
- JUMP W 0.5Hz
- F-22 IPS TIME 1.0s
- IPS WAIT 1.0s
A34 IPS POWR ALM
- IPS TRIP OFF
A64 F-30 F-MAX-L 120Hz
- F-25 S-LOCK MD1
- F-28 STOP-SW ON
- F-29 F/R SW FRE
- F/R PREEV OFF
A48 F-31 IN ANA 10V
A26 IN EXS 0.0Hz
A27 IN EXE 0.0Hz
- IN EX%S 0%
- IN EX%E 100%
- IN LEVEL 0Hz
A11 IN F-SAMP 8
A49 F-32 ARV PTN CST
A39 ARV ACC 0.0Hz
A40 ARV DEC 0.0Hz
- F-33 OV-TRQ V 100%
- OV-TRQ R 100%
C0 F-34 IN-TM 1 RS
C1 IN-TM 2 AT
C2 IN-TM 3 JG
C3 IN-TM 4 FRS
C4 IN-TM 5 CH1
C5 IN-TM 6 CF2
C6 IN-TM 7 CF1
C7 IN-TM 8 REV
J300
Function code Default
21/24
code
(Digital
operator)
A value for the second motor can be set independently by
A062 0.00
A262 in the case of the SJ300.
A value for the second motor can be set independently by
A061 0.00
A261 in the case of the SJ300.
A063 0.00
A065 0.00
A067 0.00
Note 0.50 Note: Jump frequency width setting: A064, A066, and A068
b002 1.0
b003 1.0
b001 00
b004 00
- - No need to set in the case of the SJ300
b031 01
b087 00
b035 00
b046 00
Note - Note: Please adjust with analog input setting functions
Note 0.00 Note: (SJ300) O: A011, OI: A101, O2: A111
Note 0.00 Note: (SJ300) O: A012, OI: A102, O2: A112
0(O), 20(OI),
Note Note: (SJ300) O: A013, OI: A103, O2: A113
-100(O2)
Note 100 Note: (SJ300) O: A014, OI: A104, O2: A114
Note 01(0Hz) Note: (SJ300) O: A015, OI: A105
A016 8
Note: Selection from FA1 to FA5 at an intelligent output
Note -
terminal
C042(045) 0.00
C043(046) 0.00
Note: Forward-driving/reverse-regenerating can be set
C055/C056 100
independently in the case of the SJ300.
Note: Reverse-driving/forward-regenerating can be set
C057/C058 100
independently in the case of the SJ300.
C001 18(RS)
C002 16(AT)
C003 06(JG)
C004 11(FRS)
C005 09(2CH)
03(CF2)(CE
C006 ver.)/13(USP)(UL
ver.)
C007 02(CF1)
C008 01(RV)
SJ300
Function Default setting
Remarks