Hitachi SJ300 Series Replacement Manual page 18

No. Name
1 Frequency source setting
2 Run command source setting
3 Data command method
4 Initialization mode (parameters or trip history)
5 Debug mode enable
6 Keypad RUN key routing
7 Reset mode selection
8 Base frequency setting 1
Base frequency setting 2
9 Maximum frequency setting 1
Maximum frequency setting 2
10 Start frequency adjustment
11 AVR voltage select
12 AVR function select
13 V/f characteristic curve selection 1
V/f characteristic curve selection 2
14 Auto-tuning setting
15 Motor data selection 1
Motor data selection 2
16 Motor capacity setting 1
Motor capacity setting 2
17 Motor poles setting 1
Motor poles setting 2
18 Motor constant R1 1
Motor constant R1 2
19 Motor constant R2 1
Motor constant R2 2
20 Motor constant L 1
Motor constant L 2
21 Motor constant M 1
Motor constant M 2
22 Motor constant J 1
Motor constant J 2
23 Speed response proportional constant Kp 1
Speed response proportional constant Kp 2
24 Option constant Ti 1
Option constant Ti 2
Option constant Kpp 1
Option constant Kpp 2
25 Carrier frequency setting
No. Name
J300
Function code
Default
Digital
setting
Remote Operator
operator
F9 F-SET-SELCT REM
F9 F/R-SELCT REM
- F-09 PARAM REM
- F-38 INIT TCNT CNT
- INIT DBGU OFF
F4 INIT DOPE FWD
A86 INIT RESET ON
A62 F-00 F-BASE 60
A62 F-BASE 60
A63 F-01 F-MAX 60
A63 F-MAX 60
A4 F-02 F-min 0.5
F11 F-03 AVR AC 200/400
- AVR AC ON
A0 F-04 CONTROL VC
A0 CONTROL VC
A97 F-05 AUX AUTO NOR
A98 AUX DATA TMO
A98 AUX DATA TMO
A1 AUX K Factor set
A1 AUX K Factor set
A2 AUX P 4
A2 AUX P 4
- AUX R1 Factor set
- AUX R1 Factor set
- AUX R2 Factor set
- AUX R2 Factor set
- AUX L Factor set
- AUX L Factor set
- AUX M Factor set
- AUX M Factor set
- AUX J Factor set
- AUX J Factor set
A3 AUX Kp 2.00
A3 AUX Kp 2.00
- AUX Ti 100ms
- AUX Ti 100ms
- AUX Kpp 1.00
- AUX Kpp 1.00
A10 F-36 CARRIER Factor set
J300
Function code Default
19/24
SJ300
Function
code
Default setting
(Digital
operator)
A001 02
A002 02
C070 02
b084 00
C091 00
F004 00
C102 00
A003 60
A203 60
A004 60
A204 60
b082 0.50
A082 200/400
A081 00
A044 00
A244 00
H001 00
H002 00
H202 00
H003 Factor set
H203 Factor set
H004 4
H204 4
H020 Factor set
H220 Factor set
H021 Factor set
H221 Factor set
H022 Factor set
H222 Factor set
H023 Factor set Io is set in the case of the SJ300.
H223 Factor set
H024 Factor set
H224 Factor set
H050 100.0 Motor proportional gain constant setting in the case of the
SJ300.
H250 100.0
H051 100.0
Motor integral gain constant setting in the case of the SJ300.
H251 100.0
H052 1.00
H252 1.00
b083 Factor set Please refer to 4.3 Carrier Frequency.
SJ300
Function Default setting
Remarks
Remarks